Honeywell 191108AJ Owner's Manual

Honeywell 191108AJ Manual

Get Honeywell 191108AJ PDF manuals and user guides View all Honeywell 191108AJ manuals
Add to My Manuals
Save this manual to your list of manuals

Honeywell 191108AJ manual content summary:

  • Honeywell 191108AJ | Owner's Manual - Page 1
    T8190A/191108AJ, Q682 Heating or Cooling Thermostat and Wallplate or Heating/Cooling Thermostat and Subbase D.F. Rev. 9-94 ©Honeywell Inc. 1994 Form Number 69-0643-1 M3375
  • Honeywell 191108AJ | Owner's Manual - Page 2
    Welcome... to the world of energy savings with your new Honeywell thermostat. The Honeywell name is your assurance of accurate control and reliable operation for years to come. Your new thermostat will automatically lower and raise the temperature in your home one or more times every 24 hours. This
  • Honeywell 191108AJ | Owner's Manual - Page 3
    Table of Contents Page Features of Your Thermostat ...4 Setting the Temperature ...7 Inserting Timer Batteries ...8 Setting the Timer ...9 Programming ...10 Setting Subbase Switches ...13 Troubleshooting ...14 Servicing the Thermostat ...22 Cycle Rate Adjustment ...22 Thermometer Adjustment ...23
  • Honeywell 191108AJ | Owner's Manual - Page 4
    saving and normal temperature periods. 2 THERMOSTAT COVER. Lift up and remove to adjust heat anticipator. 3 THERMOMETER. Provides accurate room temperature reading. 4 TEMPERATURE SETTING LEVERS. Left (blue mark) controls the low temperature, right (red mark) controls the high temperature. 5 TIMER
  • Honeywell 191108AJ | Owner's Manual - Page 5
    and low temperature at specific time of day as set by program pins. 9 PROGRAM PINS. Must be inserted into 24hour timer dial slots to control program index wheel. 10 PIN SLOTS. Located on 24-hour dial at 10minute intervals for program pin insertion. 11 PROGRAM DIAL. 24-hour dial with
  • Honeywell 191108AJ | Owner's Manual - Page 6
    and wiring connections for heating-only or cooling-only thermostat. 15 16 SUBBASE (Optional, not included with thermostat; ordered separately.) Provides mounting base, wiring connections and manual switching control for heating/cooling thermostat. See Setting Subbase Switches section for additional
  • Honeywell 191108AJ | Owner's Manual - Page 7
    Setting the Temperature For Heating: ■ Set the left lever (blue mark) to the energy saving temperature you want when you are sleeping or your home is unoccupied. ■ Set the right lever (red mark) to the temperature you want for normal comfort periods. NOTE: You may override the time program by
  • Honeywell 191108AJ | Owner's Manual - Page 8
    by two AAA alkaline batteries (included), or by the heating or cooling control circuit. Backup batteries may be installed to supply power to the timer power is interrupted when using a 24 Vac powering method. Install batteries in thermostat as shown in Fig. 2. Once a year or when batteries are dead
  • Honeywell 191108AJ | Owner's Manual - Page 9
    Setting the Timer ■ Lift thermostat flip-up cover and you'll find the 24-hour program dial, slotted in 10-minute increments. Adjust the timer to the current time by
  • Honeywell 191108AJ | Owner's Manual - Page 10
    for the program pins that can be inserted at 10-minute intervals. ■ Lift thermostat flip-up cover and you will find the 24-hour program dial. The intervals. ■ Three red and three blue program pins are included with your thermostat. The red pins start the high-temperature period; the blue pins start
  • Honeywell 191108AJ | Owner's Manual - Page 11
    temperature (comfort period); a blue pin is inserted at 10:00 PM for low temperature (energy saving period). Two additional sets of pins are located in the program pin storage area. You can set up to six temperature changes with the pins supplied. We recommend at least five hours for each energy
  • Honeywell 191108AJ | Owner's Manual - Page 12
    WINTER SUMMER PROGRAM PROGRAM TEMPERATURE PIN IN TEMPERATURE PIN IN °F °C CONTROL °F °C CONTROL NIGHT BEGINS 58 14 BLUE 80 27 RED ENERGY 10:00 PM SAVING ENDS PERIOD 6:00 AM 68 20 RED 75 24 BLUE DAY BEGINS
  • Honeywell 191108AJ | Owner's Manual - Page 13
    operate. In heating-only applications, only heating will operate. ON-Fan operates continuously. AUTO-Fan operates with cooling equipment as controlled by the thermostat or with the heating equipment as controlled by the plenum fan switch. In electric heat, heat pump and fan coil systems, the fan is
  • Honeywell 191108AJ | Owner's Manual - Page 14
    Troubleshooting Your Honeywell thermostat requires little or no attention. Most problems can generally be traced to the following. Problem No heat. 2 Check - System switch may be in OFF or COOL position. - Fuse or circuit breaker. - Furnace power switch may be OFF. - Pilot flame may
  • Honeywell 191108AJ | Owner's Manual - Page 15
    Troubleshooting (Continued) Problem Energy saving temperature program is 12 hours. Rooms do not more time to warm up rooms. - Program pins for correct time locations. - Positions of thermostat set point levers. - Position of subbase system switch (heating-cooling model). Action Turn timer ahead
  • Honeywell 191108AJ | Owner's Manual - Page 16
    Troubleshooting (Continued) Problem Room temperatures are not correct (continued). Check - Thermostat circuits. Burner-on time too short. - Anticipator should start. If the system does not operate, call a qualified service technician. Increase anticipator setting by 0.05 (e.g., 0.4 to 0.45).
  • Honeywell 191108AJ | Owner's Manual - Page 17
    Troubleshooting (Continued) Problem No cooling. 1 Check - System switch may be in OFF or HEAT position. - Fuse or circuit breaker. - Condenser switch position. Located outdoors and may be turned off. - Thermostat system. Contact a qualified service technician for assistance. (continued) 69-0643-1
  • Honeywell 191108AJ | Owner's Manual - Page 18
    Troubleshooting (Continued) Problem Thermostat setting and thermometer reading disagree. Check - Level position of thermostat. - Area around thermostat for drafts or radiant heat. Timer does not run. - Calibration of thermometer. -Thermostat connections at the two C terminals. If no connections,
  • Honeywell 191108AJ | Owner's Manual - Page 19
    Troubleshooting (Continued) Problem Check Timer does not run (continued). - Voltage across the two C terminals. Timer loses time. - Pins in program dial. If pins are not completely seated in program dial, jamming with index wheel can occur. - Power may be interrupted. - High limit control. If
  • Honeywell 191108AJ | Owner's Manual - Page 20
    -only system. 3 If timer is not battery powered, timer may still use batteries for backup. If this Troubleshooting section did not solve the problem, call a qualified service technician or the Honeywell Customer Assistance Center, 1-800-468-1502, Monday - Friday, 7:00 AM to 5:30 PM Central time for
  • Honeywell 191108AJ | Owner's Manual - Page 21
    used to power the timer is inadequate. - Additional (separate) transformer used to power the timer has inadequate voltage. - Spring fingers on thermostat not making proper contact with subbase terminals. - Timer has failed. Action - Restore power. - Replace wiring. - Free or replace limit switch
  • Honeywell 191108AJ | Owner's Manual - Page 22
    Servicing the Thermostat Cycle Rate Adjustment The equipment should cycle on and off just enough to keep the room temperature close to the temperature lever settings. If the thermostat seems to cycle the heating system too fast or too slow, adjust the cycle rate by moving the anticipator setting
  • Honeywell 191108AJ | Owner's Manual - Page 23
    are different, insert a small screwdriver in the thermometer slot, shown in Fig. 7, and turn it until both thermometers read the same. Replace thermostat cover and put the system into operation. THERMOMETER SLOT BACKSIDE OF FLIP-UP COVER INSERT AND TURN SCREWDRIVER M1810 Fig. 7-Thermometer
  • Honeywell 191108AJ | Owner's Manual - Page 24
    If you have questions regarding the installation and programming of your Honeywell thermostat, please visit our web site at www.honeywell.com/yourhome or call the 24-hour automated information line at 1-800-468-1502. 24 69-0643-1
  • Honeywell 191108AJ | Owner's Manual - Page 25
    25 69-0643-1
  • Honeywell 191108AJ | Owner's Manual - Page 26
    26 69-0643-1
  • Honeywell 191108AJ | Owner's Manual - Page 27
    or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the product is defective or malfunctions, Honeywell shall repair or replace it (at Honeywell's option) within a reasonable period of time
  • Honeywell 191108AJ | Owner's Manual - Page 28
    Home and Building Control Honeywell Inc. 1985 Douglas Drive No. Golden Valley, MN 55422 Home and Building Control Honeywell Limited/Honeywell Limitée 740 Ellesmere Road Scarborough, Ontario Helping You Control Your World M1P 2V9 Printed in U.S.A. www.honeywell.com/yourhome
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
Heating or Cooling
Thermostat and Wallplate
or Heating/Cooling
Thermostat and Subbase
T8190A/191108AJ, Q682
D.F.
Rev. 9-94
©Honeywell Inc. 1994
Form Number 69-0643—1