Honeywell 3800G14E User Manual - Page 19

Keyboard Wedge Connection - usb

Get Honeywell 3800G14E PDF manuals and user guides View all Honeywell 3800G14E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Connecting the Imager When Powered by Host (Keyboard Wedge) An imager can be connected between the keyboard and PC as a "keyboard wedge," plugged into the serial port or connected to a portable data terminal. The following is an example of a keyboard wedge connection: 1. Turn off power to the terminal/computer. 2. Disconnect the keyboard cable from the back of the terminal/computer. 3. Connect the appropriate interface cable to the imager and to the terminal/ computer. 4. Turn the terminal/computer power back on. Note: You will not hear a power-up beep because the 3800g is factory defaulted to a USB connection. You must scan the IBM PC AT and Compatibles with CR suffix bar code on page 1-6 to enable keyboard wedge ability. Verify the imager operation by scanning a bar code from the Sample Symbols in the back of this manual. The imager beeps once. Keyboard Wedge Connection Scanning the bar code below allows operation of the 3800g as a keyboard wedge interface to an IBM PC AT with a U. S. keyboard. 3800g User's Guide 1 - 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
3800g User’s Guide
1 - 5
Connecting the Imager When Powered by Host
(Keyboard Wedge)
An imager can be connected between the keyboard and PC as a “keyboard
wedge,” plugged into the serial port or connected to a portable data terminal.
The following is an example of a keyboard wedge connection:
1.
Turn off power to the terminal/computer.
2.
Disconnect the keyboard cable from the back of the terminal/computer.
3.
Connect the appropriate interface cable to the imager and to the terminal/
computer.
4.
Turn the terminal/computer power back on.
Note:
You will not hear a power-up beep because the 3800g is factory defaulted
to a USB connection.
You must scan the
IBM PC AT and Compatibles
with CR suffix
bar code on
page 1-6
to enable keyboard wedge ability.
Verify the imager operation by scanning a bar code from the
Sample Symbols
in
the back of this manual. The imager beeps once.
Keyboard Wedge Connection
Scanning the bar code below allows operation of the 3800g as a keyboard wedge
interface to an IBM PC AT with a U. S. keyboard.