Honeywell 5800RP Installation Guide - Page 1

K0344 6/02 ® 53 5)5HSHDWHU0RGXOH ,167$//$7,21$1'6(783*8,'( INTRODUCTION The 5800RP RF Repeater Module consists of an RF receiver and a transmitter and is intended to extend the range of ADEMCO's 5800 series RF devices by 200 feet (nominal). The 5800RP receives alarm, status, and control messages from 5800 series devices, and forwards these messages to control panel connected receivers such as the 5881EN, 5883, 6128RF, 6150RF, and LYNX controls. The control then responds accordingly (arm/disarm the system, initiate an alarm, etc.). The 5800RP also transmits it's own status including tamper, AC loss and RF jam detect via a unique serial number. Status is sent whenever a change occurs or as part of a supervisory check-in message sent approximately once an hour. The 5800RP contains a rechargeable battery that provides up to 6 hours of standby operation after primary power is lost. The 5800RP features a Spatial Diversity system that virtually eliminates the possibility of "Nulls" and "Dead Spots" within the coverage area. CONTROL PANEL* KEYPAD TERMINALS ON CONTROL BOARD POWER IN 9VAC, 15VA (e.g. 1332) OR 12VDC, 100mA 5800 SERIES WIRELESS TRANSMITTER 5800RP REPEATER MODULE 2-WAY WIRELESS KEYPAD (e.g. 5827BD, 5804BD) OR 5800RL 2-WAY RELAY MODULE 2-WAY TRANSMISSION DATA OUT DATA IN TO CONTROL RECEIVER/ TRANSCEIVER *CONTROL MUST SUPPORT A 5800 SERIES RF SYSTEM Figure 1. Wireless System Overview using 5800RP Repeater Module 5800RP_block-00-001-v0 INSTALLING THE 5800RP MODULE Mount the 5800RP remotely in its own housing following the steps below, and avoid mounting the module with its antennas touching a metal surface. Check for RF Interference: Before mounting permanently, use the red RF Interference LED to check for strong local radio frequency interference at the intended mounting location. If this LED is continuously lit, the 5800RP module should be relocated. Removing the Cover: Remove the 5800RP's cover by inserting and twisting a screwdriver blade in the slot at the center of the cover's lower edge. Note that removing the cover also places the 5800RP in the Go/No Go Test mode. This decreases its range during installation to insure an adequate margin during normal operation. Mounting the Module 1. For concealed wiring, route power wires through the rectangular opening at the rear of the base before mounting. For surface wiring entry, a thin breakaway area is provided along the base's right edge. 2. Mount the module in the selected location. For greatest security, use all four mounting holes (two keyslot holes and two round holes) in the plastic base. 3. Install each antenna in the respective right-hand terminal of the two terminal blocks at the upper edge of the 5800RP's circuit board, and tighten the screws to secure them. 4. Affix the Summary of Connections label to the inside of the module's cover. Make sure the arrows and large 'plus sign' on the label line up with the corresponding posts in the cover. 5. If applicable, set the Site ID by referring to the Setting the Site ID section on the next page. Connecting the Power Supply The 5800RP can be powered from either an AC or DC external power source connected to terminals 1 and 2 (see figure 2). Power source ratings are as follows: Type AC DC Rating 9VAC, 15VA (e.g., ADEMCO 1332) 12VDC, 100 ma 6. Connect the power supply to the 5800RP's terminals. Refer to Figure 2. These terminals are not polarized. The leads from DC supplies may be connected to either terminal. NOTE: Use of power sources with higher or lower voltages may result in damage or failure to operate properly. Non-ADEMCO power supplies may have connectors installed. Remove the connectors prior to attempting to connect power supply to 5800RP. Connecting the Battery 7. Begin battery installation by attaching an adhesive backed hook and loop fastener strip (supplied) to the Summary of Connections label in the cover. Place the strip within the large box drawing labeled 'PLACE BATTERY HERE'. Refer to Figure 2. 8. Attach another adhesive backed hook and loop fastener strip to the battery. Attach the battery to the cover by firmly pressing the two hook and loop fastener strips together. Make sure the battery is positioned as shown in Figure 2. 9. Plug the battery cable into the battery connector on the 5800RP PCB. Refer to Figure 2. CHARGING NOTE: The battery must be allowed to charge at least 12 hours in order to reach its full capacity. 10. Replace the cover on the 5800RP, being careful not to pinch the battery wires between the cover and case or any PCB components. ANTENNAS (INSERT IN RIGHT-HAND TERMINALS) MOUNTING HOLES (4) BATTERY CONNECTOR 5800RP CIRCUIT BOARD RF INTERFERENCE RED INDICATOR LIGHTS RED WHEN SETTING SITE ID GRN YEL RED DIP SWITCH ON OFF 123 45 67 8 TO POWER SUPPLY WIRING OPENING KNOCKOUT AREA FOR SURFACE WIRING POWER TERMINALS TAMPER SWITCH 5800RP_conn-00-001-V0 BATTERY AFFIX SUMMARY OF CONNECTIONS LABEL HERE MODULE COVER Figure 2. 5800RP Repeater Module Layout and Connections