Honeywell 5894PI Installation Instructions - Page 1
Honeywell 5894PI - Ademco Wireless PIR Motion Sensor Manual
UPC - 781410691292
View all Honeywell 5894PI manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
K5942V2 7/04 5894PI PASSIVE INFRARED MOTION DETECTOR/TRANSMITTER INSTALLATION INSTRUCTIONS GENERAL INFORMATION The 5894PI Passive Infrared Motion Detector/Transmitter is a 10-year batteryoperated wireless device intended for use as part of a 5800 series wireless alarm system. Designed for use in commercial and residential installations, the 5894PI is a wall-mounted unit with a standard lens that provides wide-angle protection up to a range of 35 ft (10.6m). For best coverage, mount the detector so that the likely direction of intruder motion is across the pattern. When installed per the guidelines, the TierBalanced Optics technology in the 5894PI provides false alarm protection against pets and other animals up to 80 lbs. This document provides installation instructions for the 5894PI, but the installer must be familiar with the installation instructions for the 5800 Wireless Alarm System with which the 5894PI is intended to be used. FEATURES • Tier-Balanced Optics provides pet immunity against animals up to 80 lbs. • Wireless operation for fast installation. • Dual-element pyroelectric sensor provides positive protection while minimizing false alarms. • Selectable PIR sensitivity. • Provision to turn LED on while Walk Testing (LED is turned off after testing). • Tamper-protected cover and wall; detector transmits message if cover or detector is removed. • Wall or corner mounting options. • Patented Black Bug Guard. • Temperature compensation. SPECIFICATIONS Pet Immune Lens: 35 ft x 45 ft (10.6m x 13.7m). 28 zones (8 over, 8 long range, 8 intermediate, 4 short-range). Pulse Processing: Intermediate, Standard, or Harsh, Installerselectable. Note: For pet immune applications, see Special Instructions for Installations with Pets on page 3. Detectable Walk Rate: 0.5-10 ft/Sec (0.15-3m/Sec). Mounting Height: 7.0 ft (2.1m) Walk Test Indicator: Red LED with enable/disable link. Batteries: Three 3-volt Lithium batteries. Use only ADEMCO No. 466, Duracell DL123A, Panasonic CR123A, Sanyo CR123A, or Varta CR123A. 0perating Temperature: 32°F - 122°F (0°C - 50°C). Operating Humidity: Up to 95% RH (max.), non-condensing. Dimensions: 3.0"W 5.0"H x 1.7"D (76.3mm x 127.0mm x 42.6mm). Approvals/Listings: FCC, IC, cULus, C-Tick TOP VIEW 22.5' SYSTEM DESCRIPTION Optical System The 5894PI uses efficiently designed Fresnel lenses with Tier-Balanced Optics. Radio Transmitter The built-in transmitter serves only as the communication link to the alarm system's Receiver/Control, and can send alarm, tamper, supervisory, and battery status messages to the system's receiver/control. The transmitter is not used for detection purposes. Each detector has a unique ID code permanently assigned at the factory. You must enroll this ID into the control system at the time of installation. This allows each detector used in the system to be uniquely identified. You must program the control to enroll the 5894PI as an "RF" type unit (i.e., supervised RF). To conserve battery life during normal operation, no more than one transmission sequence will occur within a 3-minute period. There is no such time restriction in Test mode (refer to the Walk Test section). 0 22.5' 10' 20' 30' 35' SIDE VIEW ALTERNATE COUNT POLARITY EACH ZONE CONSISTS OF 2 FIELDS 7' 0 0 10' 20' 30' 35' Figure 1. Protection Pattern BATTERY ACTIVATION/INSTALLATION 1. Remove front cover by pressing the front cover latch and lifting the cover off. See Figure 2. Figure 2. Remove the Front Cover 2. To activate the installed batteries, remove the battery pull-tab. (See Figure 3.) Make sure the batteries remain firmly seated in the battery holders. . Figure 3. Remove Pull Tab to activate batteries 3. To replace the batteries, remove the old batteries from the holder. Then, observing correct polarity, install three new Lithium batteries into the battery holders, as shown in Figure 4. Make sure the batteries are firmly seated. 4. Replace the cover (snap fit). Battery Caution Risk of fire, explosion, and burns. Do not recharge, disassemble, heat above 100°C, or incinerate. Dispose of used batteries promptly. Keep away from children. Page 1