Honeywell 6160V Installation Guide - Page 2

SETTING THE KEYPAD OPTIONS The procedures that follow are used to set the keypad address, voice chime mode, and additional voice keypad mode. Setting The Keypad Address When used with the VISTA-15P/VISTA-20P control panels, address 16 must be assigned to the first Keypad. Additional Keypads must be set at 17 - 23 and must be enabled additionally in control programming (fields *190 - *196). The keypad can either be set for an address of 00-30 or for non-addressable mode (31). The default keypad address is 31. For valid address settings for your keypad, refer to the control panel's Installation & Setup Guide. Note: • If unable to enter the address mode, power down, power up, and try again. • If 10 seconds pass with no key entry, the keypad automatically exits the address mode. You must power down, power up, and start the address mode again. • The keypad will not enter the address mode if the control panel is in programming mode. 1. Apply power to the keypad. 2. Within 60 seconds of applying power to the keypad, press and hold down the [1] key and [3] key at the same time for 3 seconds. The current keypad address will be displayed. 3. Press "00". The current address is cleared. 4. Enter desired keypad address. 5. Press [✱] to save the displayed address and enter the Voice Chime mode. "VOICE CHIME" (alpha keypad) or "C" (fixed keypad) is displayed along with the selected mode "1" or "0". Setting The Voice Chime Mode 6. Press [1] to set the Voice Chime mode on or press [0] to set the Voice Chime mode off. 7. Press [✱] to save the displayed Voice Chime mode and enter the Additional Console voice keypad mode. "ADDITIONAL CON" (alpha keypad) or "A" (fixed keypad) is displayed along with the selected mode "1" or "0". Note: Setting Voice Chime mode off does not effect the voice status or alarm annunciation. Setting The Additional Console Mode The Additional Console mode must be set for all voice keypads being used. 8. Set the voice keypad Additional Console mode as follows: a. On the Primary voice keypad, press [0] to set the Additional Console mode to NO. b. On any secondary voice keypads, press [1] to set Additional Console mode to YES. 9. Press [✱] to save the mode. VIEWING THE KEYPAD ADDRESS Press and hold down the [1] key and [3] key at the same time for about 3 seconds. The current address is displayed. No key entry is allowed. Press any key to exit or wait 10 seconds to exit the viewing mode. SPECIFICATIONS Physical: 6150V: 6160V: 4-7/8"H x 6-1/4"W x 1"D 5-5/16"H x 7-3/8"W x 1-3/16"D Displays: 6150V: 6160V: Fixed-Word LCD (backlit) 2 x 16 Alpha-Numeric Super twist LCD (backlit) Sounder: Speaker Electrical: Voltage: Current: +12VDC 6150V: 160mA (ARMED LED lit, LCD backlight and sounder on) reduces to 60mA when panel is operating in standby mode (backlight off). 6160V: 190mA (ARMED LED lit, LCD backlight and sounder on) reduces to 60mA when panel is operating in standby mode (backlight off). TABLE 1. ZONE DESCRIPTORS AND INDEX ENTRIES ALARM 002 DOOR 057 KITCHEN 105 PATIO 146 UPSTAIRS 207 ATTIC 009 EMERGENCY 067 LAUNDRY 106 POLICE 151 UTILITY 208 BABY 012 EXIT 071 LIBRARY 109 POOL 152 WINDOW 217 BACK 013 FIRE 079 LIVING 113 ROOM 162 YARD 223 BASEMENT 016 FLOOR 080 MAIN 122 SHED 168 ZONE 225 BATHROOM 017 FRONT 085 MASTER 123 SHOP 170 1ST 228 BEDROOM 019 GARAGE 089 MEDICAL 125 SIDE 173 2ND 230 CLOSED 040 GUN 094 MOTION 131 SLIDING 175 3RD 232 DEN 050 HALL 095 OFFICE 136 SMOKE 176 DETECTOR 052 HOUSE 099 OPEN 138 STORAGE 185 DINING 053 INSIDE 101 PANIC 144 SUPERVISED 190 REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM. ¬.9l K0022V2 12/01 Rev. B 165 Eileen Way, Syosset, New York 11791 Copyright © 2004 Honeywell International Inc. www.honeywell.com/security