Honeywell HWM330 Owners Manual - Page 8

Power, Step 1: Power, Step 2: Output / Moisture Control, Step 3: Timer Control, Refill / Clean - tank

Page 8 highlights

QuickSteam_OM_04-25-06.qxd 4/25/06 4:53 PM Page 8 EasySet™ Control Operation (Model HWM-335) cont'd. REFILL / CLEAN INDICATOR Fig. 14 • When the Refill/Clean indicator light is illuminated it implies your unit is out of water or you need to clean your humidifier (Fig. 14). • Check your water level. If the Tank is empty, remove the Tank and refill it as described in the FILLING section. • Press the Reset button to restart the humidifier after the Tank is reinstalled. • The humidifier will then resume to its previous settings. Refill/Clean Light (illuminated) Reset Button • If the water level is full, this implies it's time to clean your humidifier. Please turn off and unplug the unit and refer to the CLEANING section. NOTE: Do not press the Reset button until the Tank is refilled and reinstalled. NOTE: Your unit's performance will decrease if you do not clean your Heating Plate. You unit may continuously shut off and output will decrease. Digital EasySet™ Control Operation (Model HWM-450) POWER CAUTION: DO NOT PLUG IN THE HUMIDIFIER WITH WET HANDS AS AN ELECTRICAL SHOCK COULD OCCUR. • With the power OFF, plug the filled humidifier into a polarized 120V outlet. DO NOT FORCE THE POLARIZED PLUG INTO THE OUTLET; it will only fit one way. STEP 1: POWER • Press the Power button to start the humidifier. Your humidifier will automatically start on High power, continuous run. The display will be illuminated and will reflect the current room humidity (Fig. 15). • To turn your humidifier OFF simply press the Power button again. Fig. 15 Desired Humidity Light Moisture Control Refill/Clean Light Power Button (On/Off) Fig. 16 Timer Control Humidistat Control Reset Button STEP 2: OUTPUT / MOISTURE CONTROL Your unit has three output/moisture levels: HIGH: For fast humidifying MED: For everyday moisture control LOW: For minimum operation (ideal for nighttime use) Reset • To change your moisture level, press the moisture control button Button ( ) up or down (Fig. 16). • Once you have selected your moisture level the display will go back to showing the current room humidity after 3 seconds. NOTE: If you wish to change or check your output/moisture setting simply press the Moisture Control button once and it will show you your setting. If you would like to change it, continue to push the button up or down until you have reached your desired setting. Again, after 3 seconds the display will revert to showing the current room humidity. Continuous Mode: Your unit will run continuously at your selected output level until you shut it off or it runs out of water. STEP 3: TIMER CONTROL • You can set your Timer for up to 18 hours. This function should only be used if you desire that the humidifier be automatically shut off after a certain period of time. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

POWER
CAUTION: DO NOT PLUG IN THE HUMIDIFIER WITH
WET HANDS AS AN ELECTRICAL SHOCK COULD
OCCUR.
• With the power OFF, plug the filled humidifier into a polarized 120V
outlet. DO NOT FORCE THE POLARIZED PLUG INTO THE OUTLET; it will
only fit one way.
STEP 1: POWER
• Press the Power button to start the humidifier.Your humidifier will
automatically start on High power, continuous run. The display will be
illuminated and will reflect the current room humidity (Fig. 15).
• To turn your humidifier OFF simply press the Power button again.
STEP 2: OUTPUT / MOISTURE CONTROL
Your unit has three output/moisture levels:
HIGH: For fast humidifying
MED: For everyday moisture control
LOW: For minimum operation (ideal for nighttime use)
• To change your moisture level, press the moisture control button
(
) up or down (Fig. 16).
• Once you have selected your moisture level the display will go back to showing the current room
humidity after 3 seconds.
NOTE:
If you wish to change or check your output/moisture setting simply press the Moisture Control
button once and it will show you your setting. If you would like to change it, continue to push the button up
or down until you have reached your desired setting. Again, after 3 seconds the display will revert to
showing the current room humidity.
Continuous Mode: Your unit will run continuously at your selected output level until you shut it off or it runs
out of water.
STEP 3: TIMER CONTROL
• You can set your Timer for up to 18 hours.
This function should only be used if you desire that the
humidifier be automatically shut off after a certain period of time.
8
Digital EasySet
Control Operation (Model HWM-450)
Humidistat
Control
Moisture
Control
Timer
Control
Desired
Humidity
Light
Refill/Clean
Light
Reset
Button
EasySet
Control Operation (Model HWM-335) cont’d.
REFILL / CLEAN INDICATOR
When the Refill/Clean indicator light is illuminated it implies your unit is
out of water or you need to clean your humidifier (Fig. 14).
Check your water level. If the Tank is empty, remove the Tank and refill it
as described in the FILLING section.
Press the Reset button to restart the humidifier after the Tank is
reinstalled.
The humidifier will then resume to its previous settings.
If the water level is full, this implies it’s time to clean your
humidifier. Please turn off and unplug the unit and refer to the CLEANING section.
NOTE: Do not press the Reset button until the Tank is refilled and reinstalled.
NOTE: Your unit’s performance will decrease if you do not clean your Heating Plate.You unit may
continuously shut off and output will decrease.
Fig. 14
Refill/Clean
Light
(illuminated)
Fig. 15
Fig. 16
Reset
Button
Reset
Button
Power Button
(On/Off)
QuickSteam_OM_04-25-06.qxd
4/25/06
4:53 PM
Page 8