Honeywell MK9520-37A38 User Manual - Page 11

Installing the Scanner to the Host System, RS232, Laser Emulation, and Light Pen Emulation

Get Honeywell MK9520-37A38 PDF manuals and user guides View all Honeywell MK9520-37A38 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

INSTALLING THE SCANNER TO THE HOST SYSTEM RS232, Laser Emulation, and Light Pen Emulation 1. Turn off the host system. 2. Connect the 10-pin RJ45 male connector into the jack on the scanner. There will be an audible click when the connector lock engages. If the scanner is receiving power from the host system, skip to step #5. 3. Connect the L-shaped plug of the power supply into the power jack on the PowerLink cable. 4. Verify the AC input requirements of the power supply match the AC outlet. Connect the power supply into an AC outlet. The outlet should be near the equipment and easily accessible. 5. Connect the PowerLink cable to the proper port on the host system. Figure 6. 6. Turn on the host system. Plugging the scanner into a port on the host system does not guarantee that scanned information will be communicated properly to the host system. Please refer to the MetroSelect Single-Line Configuration Guide or MetroSet2's help files for instructions on changing the scanner's factory default configuration. The scanner and host system must use the same communication protocols. All MS95x0-00 scanners leave the factory with the Laser Emulation Mode enabled. If you recall defaults while re-configuring your scanner the Laser Emulation Mode will no longer be enabled. Refer to the MS95x0-00 Laser Emulation Mode section of the MetroSelect SingleLine Configuration Guide for information on enabling the Laser Emulation Mode. See caution on page 6. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
7
I
NSTALLING THE
S
CANNER TO THE
H
OST
S
YSTEM
RS232, Laser Emulation, and Light Pen Emulation
1.
Turn off the host system.
2.
Connect the 10-pin RJ45 male
connector into the jack on the
scanner.
There will be an audible
click
when the connector lock
engages.
If the scanner is receiving
power from the host system,
skip to step #5.
3.
Connect the L-shaped plug of the
power supply into the power jack
on the PowerLink cable.
4.
Verify the AC input requirements of
the power supply match the AC
outlet.
Connect the power supply
into an AC outlet.
The outlet should
be near the equipment and easily
accessible.
5.
Connect the PowerLink cable to
the proper port on the host system.
6.
Turn on the host system.
Plugging the scanner into a port on the host system does not guarantee
that scanned information will be communicated properly to the host
system.
Please refer to the MetroSelect Single-Line Configuration
Guide or MetroSet
2
’s help files for instructions on changing the
scanner’s factory default configuration.
The scanner and host system
must use the same communication protocols.
All MS95
x
0-
00
scanners leave the factory with the
Laser Emulation
Mode
enabled.
If you
recall defaults
while re-configuring your scanner
the
Laser Emulation Mode
will no longer be enabled.
Refer to the
MS95
x
0
-00
Laser Emulation Mode
section of the MetroSelect Single-
Line Configuration Guide for information on enabling the
Laser
Emulation Mode.
See caution on page 6
.
Figure 6.