Honeywell MK9520-37A38 User Manual - Page 32

Troubleshooting Guide, Ack/nak, Rts/cts, Xon/xoff Or

Get Honeywell MK9520-37A38 PDF manuals and user guides View all Honeywell MK9520-37A38 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

TROUBLESHOOTING GUIDE Symptoms Possible Causes Solution The unit powers up, but does not scan and/or beep. The bar code being scanned does not satisfy the configured criteria for character length lock or minimum length. Verify that the bar code being scanned falls into the configured criteria. The scanner defaults to a minimum of 3 character bar code. The following item is only relevant for RS232 and Serial Emulation USB interfaces. The unit scans a The unit is configured bar code, but to support some form locks up after the of host handshaking first scan and the but is not receiving the red* LED stays on. signal. If the unit is setup to support ACK/NAK, RTS/CTS, XON/XOFF or D/E, verify that the host cable and host are supporting the handshaking properly. The unit scans, but the data transmitted to the host is incorrect. The unit beeps at some bar codes but NOT for others of the same bar code symbology. The unit's data format does not match the host system's requirements. The bar code may have been printed incorrectly. The unit is not configured correctly for the type of bar code being scanned. The minimum symbol length setting does not work with the bar code. Verify that the unit's data format matches that required by the host. Make sure that the unit is connected to the proper host port. Check if it is a check digit/character or border problem. Check if the correct minimum symbol length is set. The unit scans the bar code but there is no data. The unit's configuration Make sure the scanner is configured is not correct. for the appropriate mode. The host is receiving data but the data does not look correct. The scanner and host may not be configured for the same interface parameters. Check that the scanner and the host are configured for the same interface parameters. Characters are being dropped. Inter-character delay needs to be added to the transmitted output. Add some inter-character delay to the transmitted output by using the MetroSelect Single-Line Configuration Guide. * In some custom units, the standard green LED has been replaced with a blue LED and the red LED has been replaced with a white LED. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
28
T
ROUBLESHOOTING
G
UIDE
Symptoms
Possible Causes
Solution
The unit powers
up, but does not
scan and/or
beep.
The bar code being
scanned does not
satisfy the configured
criteria for character
length lock or minimum
length.
Verify that the bar code being
scanned falls into the configured
criteria.
The scanner defaults to a minimum
of 3 character bar code.
The following item is only relevant for RS232 and Serial Emulation USB interfaces.
The unit scans a
bar code, but
locks up after the
first scan and the
red* LED stays on.
The unit is configured
to support some form
of host handshaking
but is not receiving the
signal.
If the unit is setup to support
ACK/NAK, RTS/CTS, XON/XOFF or
D/E, verify that the host cable and
host are supporting the handshaking
properly.
The unit scans,
but the data
transmitted to the
host is incorrect.
The unit’s data format
does not match the
host system’s
requirements.
Verify that the unit’s data format
matches that required by the host.
Make sure that the unit is connected
to the proper host port.
The bar code may
have been printed
incorrectly.
The unit is not
configured correctly for
the type of bar code
being scanned.
Check if it is a check digit/character
or border problem.
The unit beeps at
some bar codes
but NOT for
others of the
same bar code
symbology.
The minimum symbol
length setting does not
work with the bar code.
Check if the correct minimum
symbol length is set.
The unit scans
the bar code but
there is no data.
The unit’s configuration
is not correct.
Make sure the scanner is configured
for the appropriate mode.
The host is
receiving data
but the data does
not look correct.
The scanner and host
may not be configured
for the same interface
parameters.
Check that the scanner and the host
are configured for the same
interface parameters.
Characters are
being dropped.
Inter-character delay
needs to be added to
the transmitted output.
Add some inter-character delay to
the transmitted output by using the
MetroSelect Single-Line
Configuration Guide.
*
In some custom units, the standard green LED has been replaced with a blue LED and the red
LED has been replaced with a white LED.