Honeywell V5100N Use and Care Guide - Page 4

Using Your Ultrasonic Humidifier, Operating Instructions - replacement tank

Get Honeywell V5100N - Vicks Ultrasonic Humidifier PDF manuals and user guides
UPC - 328785251005
View all Honeywell V5100N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

Using Your Ultrasonic Humidifier First Time Use Read all instructions before using this appliance. Unpack and remove all packing material from the Water Tank, Mist Nozzle and Base. Completely unravel power cord and place unit on a flat, stable surface. If a demineralization cartridge is included, remove its protective wrapper and replace it into the Base as illustrated above. Follow the directions below to fill and operate the humidifier. Filling the Water Tank Always UNPLUG the humidifier before filling. 1. Remove the Directional Mist Nozzle from the Water Tank. Remove the Water Tank from the Base and turn it upside down. Turn the Tank Cap counterclockwise to open. Rinse and wipe clean. 2. Fill the Water Tank with clean, cool, tap water and replace the Tank Cap by firmly turning clockwise. Turn the Tank upright and check Tank Cap for leaks. If any water drips from Tank Cap, remove it and re-tighten. Use of very cold water may temporarily reduce the mist output. Never fill the humidifier with hot or warm water as this could cause damage and void your warranty. To avoid white dust we recommend using a Kaz Demineralization Cartridge (Model DC-51) and replacing it after 30-40 fillings. If you live in an extremely hard water area you may also wish to use distilled water to further reduce white dust. Refer to About White Dust. 3. Inspect the Base and Nebulizer for cleanliness. Refer to Care and Cleaning section. 4. Replace the Water Tank on the Base and reinstall the Mist Nozzle on the Water Tank. Operating Instructions 1. Do not operate the humidifier without water in the Water Tank. 2. After filling the humidifier, be sure the Power Switch is in the OFF position, then plug the power cord into a 120 volt AC wall outlet. 3. Slide the Power Switch to the On position. The Power Indicator will illuminate. 4. Set the Mist Intensity Control to the desired setting. To increase mist, slide Control to the right; slide Control to the left to decrease mist. 5. Mist will not appear immediately; allow a few minutes for the water to fill the Reservoir. If you are using a new Demineralization Cartridge, it may take up to fifteen minutes for the filtering material to become saturated and for mist to appear. 6. Direct Mist Nozzle away from walls and furniture. If condensation forms on walls or windows, or if indoor relative humidity exceeds 50%, reduce Mist Intensity Control setting, open door to room where humidifier is operating, or turn unit off.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
Using Your Ultrasonic Humidifier
First Time Use
Read all instructions before using this appliance.
Unpack and remove all packing material from the Water Tank, Mist Nozzle and Base.
Completely unravel power cord and place unit on a flat, stable surface. If a demineralization
cartridge is included, remove its protective wrapper and replace it into the Base as illustrated
above. Follow the directions below to fill and operate the humidifier.
Filling the Water Tank
Always UNPLUG the humidifier before filling.
1.
Remove the Directional Mist Nozzle from the Water Tank. Remove the Water Tank from
the Base and turn it upside down. Turn the Tank Cap counterclockwise to open. Rinse and
wipe clean.
2.
Fill the Water Tank with clean, cool, tap water and replace the Tank Cap by firmly turning
clockwise. Turn the Tank upright and check Tank Cap for leaks. If any water drips from
Tank Cap, remove it and re-tighten.
Use of very cold water may temporarily
reduce the mist output. Never fill the humidifier with hot or warm water as
this could cause damage and void your warranty.
To avoid white dust we recommend using a Kaz Demineralization Cartridge (Model DC-51)
and replacing it after 30-40 fillings. If you live in an extremely hard water area you may
also wish to use distilled water to further reduce white dust. Refer to
About White Dust
.
3.
Inspect the Base and Nebulizer for cleanliness. Refer to
Care and Cleaning
section.
4.
Replace the Water Tank on the Base and reinstall the Mist Nozzle on the Water Tank.
Operating Instructions
1.
Do not
operate the humidifier without water in the Water Tank.
2.
After filling the humidifier, be sure the Power Switch is in the OFF position, then plug the
power cord into a 120 volt AC wall outlet.
3.
Slide the Power Switch to the On position. The Power Indicator will illuminate.
4.
Set the Mist Intensity Control to the desired setting. To increase mist, slide Control to the
right; slide Control to the left to decrease mist.
5.
Mist will not appear immediately; allow a few minutes for the water to fill the Reservoir. If
you are using a new Demineralization Cartridge, it may take up to fifteen minutes for the
filtering material to become saturated and for mist to appear.
6.
Direct Mist Nozzle away from walls and furniture. If condensation forms on walls or
windows, or if indoor relative humidity exceeds 50%, reduce Mist Intensity Control
setting, open door to room where humidifier is operating, or turn unit off.