Honeywell VISTA 15P User Guide - Page 28

Example of Macro Programming, Using a Programmed Macro Key - user codes

Get Honeywell VISTA 15P - Ademco 6 Zone Control Panel PDF manuals and user guides
UPC - 781410414846
View all Honeywell VISTA 15P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Macro Key Programming & Usage (cont'd) The keypad beeps to acknowledge your input and displays the command you entered (followed by "F"). 4. Enter the next command, followed by press/holding the "D" key for at least two seconds. The keypad beeps and displays the keystrokes entered so far. 5. Repeat until the all the desired commands (up to 16 characters including the "F"s) have been entered. Be sure to check your keystrokes before continuing. If you made a mistake, you must start over. 6. To exit, press/hold the "D" key for at least two seconds. The display returns to system status and indicates system is ready. Example of Macro Programming Suppose you want to (1) bypass the two upstairs window zones, then (2) turn on an exterior light, and then (3) arm the security system in the AWAY mode. The procedures in the table that follows show you how you would program this macro: Typical Macro Alpha Display: MACRO PGM 60203F#701F2F Function Keystrokes Required Keypad Display 1. Bypass zones 02 & 03 2. Insert terminator 3. Turn light on (device 01) 4. Insert terminator 5. Arm system AWAY 6. Insert terminator Press BYPASS [6] key, then 2-digit zone numbers 02 & 03. Press the "D" key for at least 2 seconds. Press [#] and 7 key for "device ON", and [01] key for selecting device 1. Press the "D" key for at least 2 seconds. Press AWAY [2] key. Press the "D" key for at least 2 seconds. 60203 60203F 60203F#701 60203F#701F 60203F#701F2 60203F#701F2F Using a Programmed Macro Key ∗∗∗∗DISARMED READY TO ARM ENTER USER CODE 1. Press the Macro key programmed for the desired series of commands for at least 2 seconds. The "Enter User Code" prompt appears. The prompt remains displayed for up to 30 seconds. 2. Enter your 4-digit user code. The programmed macro sequence begins automatically after the user code is entered. - 28 - National Security Systems Inc (800) 457-1999

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
–
28
–
Macro Key Programming & Usage
(cont’d)
The keypad beeps to acknowledge your input and displays the command you
entered (followed by “F”).
4. Enter the next command, followed by press/holding the “D” key for at least two
seconds. The keypad beeps and displays the keystrokes entered so far.
5. Repeat until the all the desired commands (up to 16 characters including the “F”s)
have been entered
.
Be sure to check your keystrokes before continuing. If you made a mistake, you
must start over.
6.
To exit, press/hold the “D” key for at least two seconds. The display returns to
system status and indicates system is ready.
Example of Macro Programming
Suppose you want to (1) bypass the two upstairs window
zones, then (2) turn on an exterior light, and then (3) arm
the security system in the AWAY mode. The procedures
in the table that follows show you how you would
program this macro:
Typical Macro Alpha Display:
MACRO PGM
60203F#701F2F
Function
Keystrokes Required
Keypad Display
1.
Bypass zones 02 & 03
Press
BYPASS [6]
key, then
2-digit zone numbers 02 & 03.
60203
2.
Insert terminator
Press the “D” key for at least 2 seconds.
60203F
3.
Turn light on
(device 01)
Press [#] and 7 key for “device ON”, and
[01] key for selecting device 1.
60203F
#
701
4.
Insert terminator
Press the “D” key for at least 2 seconds.
60203F
#
701F
5.
Arm system AWAY
Press
AWAY [2]
key.
60203F
#
701F2
6.
Insert terminator
Press the “D” key for at least 2 seconds.
60203F
#
701F2F
Using a Programmed Macro Key
∗∗∗∗
DISARMED
∗∗∗∗
READY TO ARM
1.
Press the Macro key programmed for the desired
series of commands for at least 2 seconds. The “Enter
User Code” prompt appears. The prompt remains
displayed for up to 30 seconds.
ENTER USER CODE
∗
∗
∗
∗
2.
Enter your 4-digit user code.
The programmed macro sequence begins
automatically after the user code is entered.
National Security Systems Inc (800) 457-1999