Honeywell XK108 Owners Manual
Honeywell XK108 Manual
 |
View all Honeywell XK108 manuals
Add to My Manuals
Save this manual to your list of manuals |
Honeywell XK108 manual content summary:
- Honeywell XK108 | Owners Manual - Page 1
XL-20 Security System Owner's Manual N9824 11/97 - Honeywell XK108 | Owners Manual - Page 2
Detector Reset ...1 INTRODUCTION...2 SYSTEM REFERENCE ...3 XK-108 KEYPAD...5 TURNING THE SYSTEM ON ...8 Turn the USER CODES ...12 Add or Change a User Code 12 Delete a User Code ...12 KEYPAD FUNCTIONS...13 Turn System On Only ...13 Keypad PROBLEMS 22 LIMITED WARRANTY ...25 XL-20 Owner's Manual - Honeywell XK108 | Owners Manual - Page 3
light is lit Enter your four digit user code (or press the Arm button an exit/entry door. Enter your four digit user code (or press the Disarm button on your light is lit. STAY Followed by your user code The On/Off (arm) light and STAY followed by your user code The On/Off light, the Instant - Honeywell XK108 | Owners Manual - Page 4
system. The keypad is the input and display device for your security system. Your system uses a XK-108 keypad. The XK-108 is a surface mount keypad containing indicator STAY CODE Button labeled CODE Four digit user code Please keep your manual in a convenient location so you can refer to it - Honeywell XK108 | Owners Manual - Page 5
into my system. Both Buttons must be pressed at the same time to activate the alert. The buttons you press depend on which type of keypad you have. Your installer will show you how to activate these emergency keys. ZONE Left Center Right DESCRIPTION BUTTONS # & * 7 & 9 1 & 3 XL-20 Owner - Honeywell XK108 | Owners Manual - Page 6
USER ID 1 2 3 4 5 6 ASSIGNED TO (MASTER USER 1) *Master User can add, change, or erase other user codes. Monitoring Station Information Account # Telephone # XL-20 Owner's Manual - Page 4 - Honeywell XK108 | Owners Manual - Page 7
TX LB 13 RF. SPVR 10 8 F AP 11 XK-108 KEYPAD 1) ZONE STATUS LEDS These LEDS display the current zone status including alarms, bypasses, troubles and faults. Each condition will cause these LEDS to operate upon failure to communicate with the Central Station. XL-20 Owner's Manual - Page 5 - Honeywell XK108 | Owners Manual - Page 8
The STAY button enables arming the system, excluding zones programmed as interior zones. This will provide exterior protection of the location while XL-20 Owner's Manual - Page 6 - Honeywell XK108 | Owners Manual - Page 9
10) CODE BUTTON The CODE button is used to enter the installer programming mode and entry of user codes. 11) KEYPAD AUXILIARY KEYS Pressing the two keys (top & bottom) labeled "P" at the same time initiates a condition BLINKING (slow) Bell Output is in supervision XL-20 Owner's Manual - Page 7 - Honeywell XK108 | Owners Manual - Page 10
security LEAVE Enter your four digit user code. The System On keypad indicate the following conditions: Fast Blink Alarm Slow Blink/Low Intensity Bypass Slow Pulse Trouble zone one and resolve the problem. When all sensors are normal problem and turn the system on normally. If the problem problem - Honeywell XK108 | Owners Manual - Page 11
system is READY; when ready press: STAY Followed by your user code. If successful the On/Off (arm) light will be when ready press: INSTANT followed by STAY followed by your user code. If successful the On/Off light, the Instant light by your user code. If successful the On/Off light and the Instant - Honeywell XK108 | Owners Manual - Page 12
protected when the system is turned on. After the bypass command has been accepted the keypad will sound one long beep and the zone or zones bypassed will slowly blink. NOTE: Temporary users (i.e. baby sitters, housekeepers, etc.) should not be shown the Bypass procedure. UNBYPASS Unbypass returns - Honeywell XK108 | Owners Manual - Page 13
neighbor's house and wait for the police. After you have turned the system off with your user code the keypad will indicate alarm memory. To clear the display of the alarm or trouble conditions and silence the audible alert : Enter your four digit user code again. XL-20 Owner's Manual - Page 11 - Honeywell XK108 | Owners Manual - Page 14
. Press the Code button followed by the four digit master user code then the user # and the new four digit user code. The keypad will beep after each digit is pressed. Master User Code User ID New User Code CODE 1-6 There is a record sheet provided in the back of the book to help you plan and - Honeywell XK108 | Owners Manual - Page 15
this code to a temporary user so they can secure the premises when they leave. KEYPAD - SEND HELP CONDITIONS you to turn the system on to the away mode without user code. # 1 Quick Forced On - Yes No If programmed 2 NOTE: A valid user code is still required to turn the system off. This feature - Honeywell XK108 | Owners Manual - Page 16
the system is armed and not in entry delay. this will start exit time, cause the keypad to beep once and allow the user to exit without disarming the system. The system will return to its last armed state after exit your daily needs. To turn chime on or off. Press # 6 XL-20 Owner's Manual - Page 14 - Honeywell XK108 | Owners Manual - Page 17
removing the restraining screw which secures the transformer to the wall. (Note: the screw is not present on the models sold in Canada.) 2. Observe that the AC indicator light on the keypad goes off. 3. Activate of your system, please contact your alarm company. XL-20 Owner's Manual - Page 15 - Honeywell XK108 | Owners Manual - Page 18
local fire authority that you have installed a fire alarm system. 8. When the fire alarm signals, LEAVE IMMEDIATELY. Do not stop for belongings. XL-20 Owner's Manual - Page 16 - Honeywell XK108 | Owners Manual - Page 19
. Everyone, including neighbors, should be familiar with your Fire and Burglary audible alarm sounders. Fire Alarm Sound is Burglar Alarm Sound is XL-20 Owner's Manual - Page 17 - Honeywell XK108 | Owners Manual - Page 20
system is an advanced design security system, it does not offer occur if a metal object is moved into the path. • A user may not be able to reach a panic or emergency button quickly enough designed ranges as diagrammed in their Installation Manual. Passive Infrared Detectors do not provide - Honeywell XK108 | Owners Manual - Page 21
premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn - Honeywell XK108 | Owners Manual - Page 22
on while leaving the interior zones off allowing you to move freely inside, opening interior doors and passing by motion detectors without causing an alarm. KEYPAD: A Keypad is your link into your system. It displays alarm and trouble messages, XL-20 Owner's Manual - Page 20 - Honeywell XK108 | Owners Manual - Page 23
The system supports up to 6 separate user codes. The system supports one master user who can add/delete other user codes. Two of the user codes may be dedicated to special functions as defined by your alarm company at the time of installation. (See the User Code List in the back of this manual) ZONE - Honeywell XK108 | Owners Manual - Page 24
to the equipment unless authorized by the installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. TELEPHONE OPERATIONAL PROBLEMS In the event of telephone operational problems, disconnect the control by removing the - Honeywell XK108 | Owners Manual - Page 25
NOTES XL-20 Owner's Manual - Page 23 - Honeywell XK108 | Owners Manual - Page 26
NOTES XL-20 Owner's Manual - Page 24 - Honeywell XK108 | Owners Manual - Page 27
serviced by anyone other than the Seller. In case of defect, contact the security professional who installed and maintains your security equipment SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHILE SHALL BE THE COMPLETE AND EXCLUSIVE 's Manual - Page 25 - Honeywell XK108 | Owners Manual - Page 28
165 Eileen Way, Syosset, New York, 11791 Copyright © 1997 PITTWAY CORPORATION N9824 11/97 XL-20 Owner's Manual - Page 26
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
 |
 |
XL-20
Security System
Owner’s Manual
N9824 11/97