Hoover F5915100 Manual - Page 13

Before using tool, After using tool

Get Hoover F5915100 PDF manuals and user guides View all Hoover F5915100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

3-9 3-10 3-11 H F G 3. Remove recovery tank front panel (F) by sliding it straight up. 4. Replace panel with converter (G). Slide converter halfway down opening until it is firmly in place. 3-12 I 3-13 J 6. The tank replaces in a hingelike manner. Position front of lid under tabs (I) on front of tank. Rotate lid down onto tank. Make sure lid is secure on all sides before cleaning. For full suction, it is important that the recovery tank lid is properly secured before cleaning. Reverse procedure to remove hose and solution tube. Raise carpet cleaner handle to upright position. K 1. Attach tool to connector end of hose by sliding it onto connector until the tab (J) locks it securely. Using your thumb, push forward and up on the latch (K) to remove tool as shown. 5. Before connecting tube (H) to cleaner, make sure black tabs are extended by pulling tan collar toward tube. Open door on hood labeled "Stair/ upholstery Cleaning Connection". Press round solution tube connector onto round projection inside door. Press connector collar down firmly to ensure that it is fully connected. Before using tool It may be necessary to remove air from the system ("prime the pump") so the clean solution will flow to the tool. Follow these steps: 1. Attach tool to hose and turn the carpet cleaner ON. 2. Put the tool on a hard surface or against your hand to block off the suction. 3. Wait a few seconds (can take up to 15 seconds). Then squeeze the trigger and begin cleaning. Follow the instructions on pages 14 and 15 for the appropriate cleaning task. 3-14 3. Disconnect carpet cleaner from 3-15 electrical outlet. L 4. Drain solution tube by placing round end in sink and raising nozzle above your head. Press the trigger. 5. Proceed with steps c, d and e for "After cleaning" on pages 10 and 11. M After using tool 1. Follow steps a and b for "After cleaning" on pages 10 and 11. 2. Drain suction hose by turning carpet cleaner ON and holding end of hose up for several seconds. Do not press trigger. Occasionally, debris may become lodged inside of the hose at the converter end (L). To clean out the hose, lift bottom of converter clip (M) with a screwdriver and remove clip. Remove debris as shown. Continued § 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
3-9
3-10
3-11
3-12
3-14
3-15
13
3. Remove recovery tank front panel
(F) by sliding it straight up.
4. Replace panel with converter (G).
Slide converter halfway down open-
ing until it is firmly in place.
5.
Before connecting tube (H) to
cleaner, make sure black tabs are
extended by pulling tan collar
toward tube.
Open door on hood labeled “Stair/
upholstery Cleaning Connection”.
Press round solution tube connector
onto round projection inside door.
Press connector collar down firm-
ly to ensure that it is fully con-
nected.
6.
The tank replaces in a hinge-
like manner.
Position front of lid
under tabs (I) on front of tank. Rotate
lid down onto tank.
Make sure lid is secure on all
sides
before cleaning.
For full suction, it is important that
the recovery tank lid is properly
secured before cleaning.
Reverse procedure to remove
hose and solution tube.
Raise carpet cleaner handle to
upright
position.
J
F
I
G
H
K
L
M
3-13
1. Attach tool to connector end of
hose by sliding it onto connector
until the tab (J) locks it securely.
Using your thumb,
push forward
and up
on the
latch (K)
to remove
tool as shown.
Before using tool
It may be necessary to remove air
from the system (“prime the pump”)
so the clean solution will flow to the
tool. Follow these steps:
1. Attach tool to hose and turn the
carpet cleaner ON.
2. Put the tool on a hard surface or
against your hand to block off the
suction.
3. Wait a few seconds (can take up
to 15 seconds). Then squeeze the
trigger and begin cleaning.
Follow the instructions on pages 14
and 15 for the appropriate cleaning
task.
After using tool
1. Follow steps a and b for “After
cleaning” on pages 10 and 11.
2. Drain suction hose by turning car-
pet cleaner ON and holding end of
hose up for several seconds.
Do
not press trigger.
3.
Disconnect carpet cleaner from
electrical outlet.
4. Drain solution tube by placing
round end in sink and raising nozzle
above your head. Press the trigger.
5. Proceed with steps c, d and e for
“After cleaning” on pages 10 and
11.
Continued
±
Occasionally, debris may become
lodged inside of the hose at the
converter end (L). To clean out the
hose, lift bottom of converter clip
(M) with a screwdriver and remove
clip. Remove debris as shown.