Hoover FH55000 Product Manual English - Page 2
Cleaning Fluid, Caution, Important, Warning
View all Hoover FH55000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
GETTING STARTED OPERATION ASSEMBLY Fully assemble product prior to use. 1 Insert the Upper Handle into Upper Handle Pole and insert Upper Handle Pole into the base. You will hear a "CLICK" when each end locks into place. 2 Slide the Clean Water Tank into place. Push down firmly. NOTE: To avoid damage to wood floors underneath area rugs or carpet, place waterproof material (ex: plastic) underneath them before cleaning. TIP BEFORE YOU BEGIN CLEANING 1 Vacuum carpet and upholstery thoroughly with a Hoover® vacuum before use. Don't use the carpet cleaner as a traditional vacuum cleaner. 2 Be sure to check Hoover Cleaning Solutions Guide and the cleaning code on your upholstery. Use your cleaner only on upholstery marked "W" or "W/S". 3 Test for colorfastness in a small, hidden area. Gently rub surface with a dampened white cloth. Wait ten minutes and check for color removal or bleed with a white paper towel. Tools and accessories vary per model. FILL THE CLEAN WATER TANK 1 Lift up to remove the Clean Water Tank, then remove the cap and add warm water to the fill line. Add Hoover Solution to the solution fill line. Secure cap. 2 Align the tank and firmly press it into place. NOTE: Cap must be locked in place for proper performance and to prevent leaking. NOTE: Read the directions on the Hoover® Carpet Cleaning fluid prior to use. CLEANING FLUID SEE THE HOOVER'S SOLUTION GUIDE insert or visit Hoover.com/cleaning-solutions. CAUTION: Not to be used for grooming a pet. CAUTION: DO NOT USE THIS EXTRACTOR ON HARD FLOORS. USING THIS PRODUCT ON HARD FLOORS MAY SCRATCH OR DAMAGE YOUR FLOOR. HOW TO CLEAN CARPETS 21 1 Step on the Handle Release Pedal to recline the cleaner into position. 2 Step on the Power Pedal to turn ON. IMPORTANT:Empty Dirty Water Tank when you hear an audible change. Ensure the tank is secured before cleaning. 3 Squeeze trigger for a slow forward and backward wet stroke. 4 Release trigger for a slow forward and backward dry stroke. To Rinse: Fill with warm water and omit adding solution to the Clean Water Tank. WARNING: Risk of personal injury - Brushroll may suddenly restart - unplug before cleaning or servicing. HOW TO CLEAN THE DIRTY WATER TANK To Dry System: Run system for ten seconds before shutting off without engaging trigger. 1 Turn power OFF and unplug the power cord. 2 Press down the top of the Dirty Water Tank. Remove Tank from carpet cleaner base at an angle. 3 Place on a flat surface and unlatch Dirty Water Tank lid to remove top of tank. 4 Empty tank, rinse, and remove all large debris from tank and openings. Allow tank to air dry. 5 Prior to replacing tank, check and clean filter as needed. CAUTION: Always turn off this product before connecting or disconnecting hose. HOW TO ATTACH/USE HOSE AND TOOL 1 Read "Before you Begin Cleaning" instructions. 2 To ensure maximum performance and to protect your carpet, be sure to place the handle in the upright position while using the hose. Placing the handle in the upright position shuts off the antimicrobial embedded brushroll. 3 To clean with hose tool, remove the nozzle cover then align the ports and plug it in firmly. 4 Connect tool to hose by sliding it onto the connector until it securely locks into place. CLEANING CARPETED STAIRS AND UPHOLSTERY CAUTION: Use extra care when cleaning on stairs. To avoid personal injury or damage, and to prevent the cleaner from falling, always place cleaner at bottom of stairs or on floor. Do not place cleaner on stairs or furniture, as it may result in injury or damage. 1 Hold tool about 5 inches over the spot or stain. Spray a generous amount of cleaning solution over the soiled area by pressing the trigger behind the tool.