Hoover PowerDash Pet Advanced Product Manual English - Page 3

2 Scrub the stain in a back and forth motion. MAINTENANCE This product contains no serviceable parts. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, call customer service at 1-800-944-9200 prior to continuing use. 3 Apply downward pressure on the front of the cleaning tool and pull toward you to extract. 4 Repeat as needed to lift the stain and suction up the dirt. HOW TO REMOVE & CLEAN THE BRUSHROLL AND REMOVE THE BELT CAUTION: To reduce the risk of injury from moving parts, unplug before servicing. TIP TO AVOID SATURATING CARPET 1 Remove the nozzle cover by pulling up and forward on the latch. Rinse nozzle cover and allow to air dry. 1 Do not use more than 4 wet strokes over any one area. Always end with dry strokes. 2 If additional cleaning is necessary, wait until the carpet is completely dry before using the tool again. HOW TO REMOVE HOSE AND TOOL 2 Gently grab the finger ledge and flip brushroll cover open. Wipe away any debris. Flip closed when finished. 1 To dry the system, run the unit for a few seconds without pressing the trigger. Turn off unit before removing attachments. Press trigger on tool to ensure all fluid has been discharged from the hose. Using your thumb, push forward and up on the latch to remove tool. 3 Press down right foot pedal to recline the machine. Lay product down to access the underside. Use a Philips screwdriver to remove 12 screws. Screws 1-2 are on the left of the brushroll. Screws 3-7 are on the top belt access cover. Screws 8-11 are on the bottom belt access cover. 2 Press button on end of hose and pull to remove hose from unit. Replace the nozzle cover. 4 Once screws 1-2 and 3-7 are removed, the brushroll and front end of the belt can be taken out. NOTE: The window will be loose at this point since the components that hold it in place are now disassembled. The window is a replaceable part. See window replacement instructions following the belt replacement instructions. 5 Screws 8 - 11 on the bottom belt access cover need to be removed. Remove Philips head screws only. 6 Now that the screws are removed, press the small white lever that is located underneath the belt. Then the rear belt access can pivot outwards as shown. The belt can now be completely removed and replaced. 7 To reassemble, just pivot the rear belt access cover back into place and fasten the screws. Reassemble the brushroll on the belt. Add the front belt access cover and brushroll endcap as they were before. NOTE: Screws for 2 and 3 are much longer than the other screws. All other screws are the same. HOW TO REPLACE BRUSHROLL WINDOW 1 Remove the nozzle cover by pulling up and forward on the latch. 2 Remove screws 1-2 and the brushroll end cap. 3 Slide out brushroll window and replace with new window 4 Replace brushroll end cap and screws. Return nozzle cover back to original location. NOTE: Rotate brushrolls manually to make sure belt is not twisted or pinched. THERMAL PROTECTOR* A thermal protector has been designed into your cleaner to protect it from overheating. When the thermal protector activates the cleaner will stop running. If this happens proceed as follows: 1. Turn cleaner OFF. 2. Empty dirty water tank. 3. Inspect the nozzle for any obstructions. Clear obstructions if present. 4. When cleaner is de-energized and motor cools for 30 minutes, the thermal protector will deactivate and cleaning may continue. If the thermal protector continues to activate after following the above steps, your cleaner needs servicing. *Available on select models. STORAGE: Wrap the power cord around the cord hooks for convenient storage. Attach the plug end to the cord. Allow brushes and underside of carpet cleaner to air dry thoroughly before storing carpet cleaner on a carpeted or wood surface. LUBRICATION: The motor and brushroll are equipped with bearings which contain sufficient lubrication for their lifetime. The addition of lubricant could cause damage. Do not add lubricant to motor or brushroll.