Hotpoint AH12H15D5B Installation Instructions - Page 4

Using The Air Conditioner, Controls

Get Hotpoint AH12H15D5B PDF manuals and user guides View all Hotpoint AH12H15D5B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

USING THE AIR CONDITIONER Controls Air Conditioner Controls ŶPOWER ‡3UHVVWKH32:(5EXWWRQWRWXUQWKHXQLWRQRURII:KHQ the unit is on,the power indicator light will be green. :KHQWKHXQLWLVRIIWKHOLJKWZLOOJRRXW ŶMODE ‡3XVKWKLVEXWWRQWRF\FOHWKURXJKWKHPRGHVIURP&22/ +($7)$1'5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
4
49-5000684
Rev. 1
POWER
the unit is on,the power indicator light will be green.
MODE
option will illuminate, identifying the mode selected.
•
COOL:
The range of set temperature is 62°F~86°F.
Cooling begins automatically when the room
temperature is above the set point,and stops when the
mode before stopping. The fan is set up from the factory
to run in continuous mode when in cooling.
•
HEAT:
The range of set temperature is 62°F~84°F.
For heat pump models the unit can alternate running
between reverse cycle heat mode and electric heater
mode according to the difference between the set
temperature and the room temperature. The fan motor
cycles on and off with the compressor and electric
heater.
The indoor fan motors starts before the compressor
and stops after the compressor cycles off.
NOTE:
Reverse cycle heating and the electric heater
no not run at the same time. In the following cases, it
is normal that the compressor does not operate.
the room temperature falls to 8°F below the set point
temperature.
cycle off while the ID fan continues to run to defrost
the coil.
• FAN:
Fan operation only without heating and cooling.
NOTE:
The set temperature ranges can be changed.
6
for details.
•
DRY:
with dehumidification.
UP/DOWN BUTTONS ( + / - )
the set temperature of the unit in cooling or heating
The set temperature appears in the display.
NOTE:
+
and
-
seconds to change the temperature display between °C
& °F scale.
FAN (FAN SPEED)
appears near the display when the fan is in constant
several seconds after the compressor
cycles off. This
DISPLAYS:
Control and Error code (on some models):
LC
The unit can only be operated by using wall thermostat.
FC
thermostat are not available. The unit can only be
Error codes:
AS
ES
CS
OS
HS
LE
NOTE:
back in.If error repeats, call for service.
LO
HI
FP
NOTE:
slightly different.
NOTE:
This air conditioner is designed to be operated
under the conditions listed above.
NOTE:
operating temperatures.
USING THE AIR CONDITIONER
Controls
Air Conditioner Controls
°F
°F
°F
°F