Hotpoint HTX26EASWWW Quick Specs - Page 2

HTX26EASWWW Hotpoint® 6.2 Cu. Ft. Capacity Electric Dryer with up to 120 Ft. Venting and Shallow Depth For complete information, see installation instructions packed with your dryer. DUCTING MATERIALS: For best performance, this dryer should be vented with 4" diameter all-rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil-type) ducting. EXHAUST LENGTH CALCULATION: 1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn. 2. The maximum length of 4' rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow. Dryers MUST be exhausted to the outside. ACCESSORIES* GE Part Number Description WX09X10002 4' 30 Amp. 3-Wire Dryer Cord WX09X10003 5' 30 Amp, 3-Wire Dryer Cord WX09X10004 6' 30 Amp 3-Wire Dryer Cord WX09X10018 4' 30 Amp. 4-Wire Dryer Cord WX09X10019 5' 30 Amp. 4-Wire Dryer Cord WX09X10020 6' 30 Amp. 4-Wire Dryer Cord WX08X10086 8' Flexible Dryer Duct with 2 screw clamps PM08X10085 8' Flexible Dryer Duct with 2 screw clamps WX8X73 8' Flexible Dryer Duct w/ 2 tension clamps PM8X73 8' Flexible Dryer Duct w/ 2 tension clamps, retail kit WX08X10130-100PK 4" Dryer Tension Clamp WX08X10131-50PK 4" Dryer Screw Clamp WX8X74 50' Dryer Duct PM08X10078 Dryer Vent Close Elbow - turns 90° within 4" PM8X85 Universal Outdoor Dryer Exhaust WE01X25160 Drying Rack WE49X22606 Rear Exhaust Opening Cover *Accessories sold separately. CAUTION: For personal safety, do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard. Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12" above the ground or any other obstruction with the opening pointed down. Dryer exhausting information - use metal duct only vertical and horizontal ducting. For every extra 90° elbow, reduce the allowable vent system length by 10 ft. Two 45° elbows will be treated like one 90° elbow. For the side exhaust installations, add one 90° elbow to the chart. When calculating the total vent system length, you must add all the straight portions and elbows of the system (including the transition duct). Laundry Center length includes factory-installed elbow that does not impact vent length. Best performance A A 4 B A Maximum length of 4" dia rigid metal duct Exhaust hood type 4 2-1/2 Domestic dryer models Number A B of 90° 4" 2-1/2" turns opening opening 0 120 ft. 90 ft. 1 100 ft. 75 ft. 2 85 ft. 65 ft. Long Vent 6.0 - 8.0 cu. ft. 3 capacity electric & gas dryers 4 (HTX26-) 5 70 ft. 60 ft. 55 ft. 55 ft. 45 ft. 35 ft. Specification Revised 2/24