Hunter 21117 Owner's Manual - Page 10

installing without the light fixture, operating your ceiling fan - weather

Get Hunter 21117 PDF manuals and user guides View all Hunter 21117 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

10 installing without the light fixture Your Hunter fan comes with an integrated light fixture assembly and an optional switch housing cap and plug button. This feature gives you the option of installing the fan with or without the included light fixture. attaching the upper switch housing 1. Partially install two #6-32 x 3/8" housing assembly screws into the switch housing mounting plate as shown in Figure 26. 2. Feed the upper plug connector through the center opening of the upper switch housing. See Figure 26. 3. Align the keyhole slots in the upper switch housing with the housing assembly screws installed previously. 4. Turn the upper switch housing counterclockwise until the housing assembly screws are firmly situated in the narrow end of the keyhole slots as shown in Figure 27. Install the one remaining #6-32 x 3/8" housing assembly screw into the third hole in the upper switch housing. Tighten all three screws firmly. CAUTION: Make sure the upper switch housing is securely attached to the switch housing mounting plate. Failure to properly attach and tighten all three housing assembly screws could result in the switch housing and light fixture falling. attaching the lower switch housing 1. Connect the upper plug connector from the motor to the lower plug connector in the lower switch housing assembly. See Figure 30. NOTE: Both plug connectors are polarized and will only fit together one way. Make sure that both connectors are properly aligned before connecting them together. Incorrect connection could cause improper operation and damage to the product. 2. Place the lower switch housing assembly over the upper switch housing. Align the side screw holes in the upper and lower switch housings. Attach the lower switch housing to the upper switch housing with three #6-32 x 3/8" housing assembly screws. See Figure 30. operating your ceiling fan 1. Turn on electrical power to the fan. 2. The fan pull chain controls power to the fan. The pull chain has four settings in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings. • Release slowly to prevent the chain from recoiling into the blades. • The chain uses a breakaway connector that separates if the chain is jerked. If this happens, simply reinsert the chain into the connector. 3. The light pull chain controls power to the light. The pull chain has two settings: On and Off. 4. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in warm weather to cool the room with a direct breeze. In winter, having the fan draw air upward (clockwise blade rotation) will distribute the warmer air trapped at the ceiling around the room without causing a draft. Refer to Figure 32. Figure 32 - Air flow patterns To change the direction of air flow, turn the fan off and let it come to a complete stop. Slide the reversing switch on the fan to the opposite position as shown in Figure 33. Restart fan. Fan Pull Chain Reversing Switch Figure 33 - Pull chain and reversing switch 41847-01 04/21/2003 © 2003 Hunter Fan Company

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
41847-01
04/21/2003
© 2003 Hunter Fan Company
10
10
10
10
10
installing without the light fixture
Your Hunter fan comes with an integrated light fixture assembly
and an optional switch housing cap and plug button.
This feature
gives you the option of installing the fan with or without the in-
cluded light fixture.
attaching the upper switch housing
1.
Partially install two #6-32 x 3/8" housing assembly screws into
the switch housing mounting plate as shown in Figure 26.
2.
Feed the upper plug connector through the center opening of
the upper switch housing. See Figure 26.
3.
Align the keyhole slots in the upper switch housing with the
housing assembly screws installed previously.
4.
Turn the upper switch housing counterclockwise until the
housing assembly screws are firmly situated in the narrow end
of the keyhole slots as shown in Figure 27. Install the one re-
maining #6-32 x 3/8" housing assembly screw into the third
hole in the upper switch housing. Tighten all three screws firmly.
CAUTION:
M
N:
M
N:
M
N:
M
N:
Make s
e s
e s
e s
e sur
ur
ur
ur
ure t
e t
e t
e t
e the up
e up
e up
e up
e upper s
r s
r s
r s
r switch h
h h
h h
h h
h housin
sin
sin
sin
sing i
g i
g i
g i
g is s
s s
s s
s s
s se-
e-
e-
e-
e-
cur
ur
ur
ur
urely a
y a
y a
y a
y attached t
d t
d t
d t
d to t
o t
o t
o t
o the s
e s
e s
e s
e switch h
h h
h h
h h
h housin
sin
sin
sin
sing m
g m
g m
g m
g moun
un
un
un
untin
in
in
in
ing p
g p
g p
g p
g plate. F
. F
. F
. F
. Fail-
il-
il-
il-
il-
ur
ur
ur
ur
ure t
e t
e t
e t
e to p
o p
o p
o p
o properly a
y a
y a
y a
y attach a
h a
h a
h a
h and t
d t
d t
d t
d tighten a
n a
n a
n a
n all t
ll t
ll t
ll t
ll thr
hr
hr
hr
hree h
e h
e h
e h
e housin
sin
sin
sin
sing a
g a
g a
g a
g as-
semb
mb
mb
mb
mbly s
y s
y s
y s
y screws c
s c
s c
s c
s coul
ul
ul
ul
uld r
d r
d r
d r
d resul
ul
ul
ul
ult in t
t in t
t in t
t in t
t in the s
e s
e s
e s
e switch h
h h
h h
h h
h housin
sin
sin
sin
sing a
g a
g a
g a
g and li
d li
d li
d li
d light
fixtur
ur
ur
ur
ure f
e f
e f
e f
e fallin
llin
llin
llin
lling.
attaching the lower switch housing
1.
Connect the upper plug connector from the motor to the lower
plug connector in the lower switch housing assembly. See Fig-
ure 30.
NOTE: Both plug connectors are polarized and will only fit to-
gether one way. Make sure that both connectors are properly
aligned before connecting them together. Incorrect connec-
tion could cause improper operation and damage to the prod-
uct.
2.
Place the lower switch housing assembly over the upper switch
housing. Align the side screw holes in the upper and lower
switch housings. Attach the lower switch housing to the up-
per switch housing with three #6-32 x 3/8" housing assembly
screws. See Figure 30.
Fan Pull
Chain
Reversing
Switch
operating your ceiling fan
1.
Turn on electrical power to the fan.
2.
The fan pull chain controls power to the fan. The pull chain
has four settings in sequence: High, Medium, Low and Off.
•
Pull the chain slowly to change settings.
•
Release slowly to prevent the chain from recoiling into the
blades.
•
The chain uses a breakaway connector that separates if
the chain is jerked. If this happens, simply reinsert the chain
into the connector.
3.
The light pull chain controls power to the light.
The pull chain
has two settings: On and Off.
4.
Ceiling fans work best by blowing air downward (counterclock-
wise blade rotation) in warm weather to cool the room with a
direct breeze. In winter, having the fan draw air upward (clock-
wise blade rotation) will distribute the warmer air trapped at
the ceiling around the room without causing a draft.
Refer to
Figure 32.
Figur
ur
ur
ur
ure 32 - A
e 32 - A
e 32 - A
e 32 - A
e 32 - Air f
ir f
ir f
ir f
ir flow p
w p
w p
w p
w patterns
To change the direction of air flow, turn the fan off and let it
come to a complete stop. Slide the reversing switch on the fan
to the opposite position as shown in Figure 33. Restart fan.
Figur
ur
ur
ur
ure 33 - P
e 33 - P
e 33 - P
e 33 - P
e 33 - Pull c
ull c
ull c
ull c
ull chain a
in a
in a
in a
in and r
d r
d r
d r
d reversin
sin
sin
sin
sing s
g s
g s
g s
g switch