Hunter 21117 Owner's Manual - Page 5

assembling the fan

Get Hunter 21117 PDF manuals and user guides View all Hunter 21117 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

4. Align the slotted holes (refer to Figure 10) in the ceiling plate with the pilot holes in the wood support structure. Note: The isolation pads should be flush against the ceiling. For Angled Ceilings: Be sure to orient the ceiling plate so that the arrows on the ceiling plate are pointing towards the ceiling peak. Refer to Figure 10. Slots Arrows for Orienting on Angled Ceiling Figure 10 - Locating the slotted holes to use 5. Place a flat washer on each of the two 3" screws and pass the screws through the slotted holes in the ceiling plate as shown in Figure 11. 6. Tighten the screws into the 9/64" pilot holes; do not use lubricants on the screws. Do not overtighten. Ceiling Joist 2 x 4 Brace Ceiling Plate Flat Washer Ceiling Outlet Box 3" Wood Screw Figure 11 - Installing the ceiling plate assembling the fan assembling the fan for a standard or angled ceiling 1. Insert the downrod through the canopy and canopy trim ring as shown in Figure 12. Feed wires from the fan through the downrod. 2. Screw the downrod into the fan assembly until tight. IMPORTANT! Tighten downrod set screw as shown in Figure 12. CAUTION: The downrod has a special coating on the threads. Do not remove this coating; the coating prevents the downrod from unscrewing. Once assembled, do not remove the downrod. 3. Continue to the hanging the fan section. 5 Hanger Ball/ Downrod Assembly Canopy Canopy Trim Ring Set Screw Figure 12 - Assembling the downrod assembling the fan for a low ceiling 1. Remove the screw on the hanger ball to disassemble it from the downrod as shown in Figure 13. Screw on the Hanger Ball Hanger Ball/ Downrod Assembly Figure 13 - Removing the screw from the hanger ball 2. Remove the hook from the assembly. 3. Completely remove the set screw (identified in Figure 12) from the fan adapter. 4. Put the set screw, previously removed, through the two black neoprene washers and the hook as shown in Figure 14. Hook must be installed in same orientation as shown in Figure 14. Black Neoprene Washer Hook Set Screw Figure 14 - Assembling the set screw for low profile assembly 5. Reassemble the set screw to the adapter as shown in Figure 14. NOTE: The rubber washers should be tight enough to keep the hook standing straight up, but the set screw should not be completely tighten as to keep the hook from being able to swing. © 2003 Hunter Fan Company 41847-01 04/21/2003

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
© 2003 Hunter Fan Company
41847-01
04/21/2003
5
4.
Align the slotted holes (refer to Figure 10) in the ceiling plate
with the pilot holes in the wood support structure.
Note: The
isolation pads should be flush against the ceiling.
For Angled Ceilings:
Be sure to orient the ceiling plate so that
the arrows on the ceiling plate are pointing towards the ceiling
peak.
Refer to Figure 10.
Figur
ur
ur
ur
ure 10 - L
e 10 - L
e 10 - L
e 10 - L
e 10 - Locatin
in
in
in
ing t
g t
g t
g t
g the s
e s
e s
e s
e slotted h
d h
d h
d h
d holes t
s t
s t
s t
s to u
o u
o u
o u
o use
5.
Place a flat washer on each of the two 3" screws and pass the
screws through the slotted holes in the ceiling plate as shown
in Figure 11.
6.
Tighten the screws into the 9/64" pilot holes; do not use lubri-
cants on the screws.
Do not overtighten.
Figur
ur
ur
ur
ure 11 - I
e 11 - I
e 11 - I
e 11 - I
e 11 - Installin
llin
llin
llin
lling t
g t
g t
g t
g the c
e c
e c
e c
e ceilin
ilin
ilin
ilin
iling p
g p
g p
g p
g plate
assembling the fan
assembling the fan for a standard or angled ceiling
1.
Insert the downrod through the canopy and canopy trim ring
as shown in Figure 12.
Feed wires from the fan through the
downrod.
2.
Screw the downrod into the fan assembly until tight.
IMPOR-
TANT!
Tighten downrod set screw as shown in Figure 12.
CAUTION:
T
N:
T
N:
T
N:
T
N:
The d
e d
e d
e d
e downr
nr
nr
nr
nrod h
d h
d h
d h
d has a s
s a s
s a s
s a s
s a special c
l c
l c
l c
l coatin
in
in
in
ing o
g o
g o
g o
g on t
n t
n t
n t
n the
thr
hr
hr
hr
hreads.
D
.
D
.
D
.
D
.
Do n
o n
o n
o n
o not r
t r
t r
t r
t remove t
e t
e t
e t
e this c
s c
s c
s c
s coatin
in
in
in
ing; t
g; t
g; t
g; t
g; the c
e c
e c
e c
e coatin
in
in
in
ing p
g p
g p
g p
g prevents
the d
e d
e d
e d
e downr
nr
nr
nr
nrod f
d f
d f
d f
d from un
m un
m un
m un
m unscrewin
in
in
in
ing.
O
.
O
.
O
.
O
.
Once a
e a
e a
e a
e assemb
mb
mb
mb
mbled, d
d, d
d, d
d, d
d, do n
o n
o n
o n
o not
remove t
e t
e t
e t
e the d
e d
e d
e d
e downr
nr
nr
nr
nrod.
d.
d.
d.
d.
3.
Continue to the hangin
in
in
in
ing t
g t
g t
g t
g the f
e f
e f
e f
e fan section.
Figur
ur
ur
ur
ure 12 - A
e 12 - A
e 12 - A
e 12 - A
e 12 - Assemb
mb
mb
mb
mblin
lin
lin
lin
ling t
g t
g t
g t
g the d
e d
e d
e d
e downr
nr
nr
nr
nrod
assembling the fan for a low ceiling
1.
Remove the screw on the hanger ball to disassemble it from
the downrod as shown in Figure 13.
Figur
ur
ur
ur
ure 13 - R
e 13 - R
e 13 - R
e 13 - R
e 13 - Removin
in
in
in
ing t
g t
g t
g t
g the s
e s
e s
e s
e screw f
w f
w f
w f
w from t
m t
m t
m t
m the h
e h
e h
e h
e hanger b
r b
r b
r b
r ball
ll
ll
ll
ll
2.
Remove the hook from the assembly.
3.
Completely remove the set screw (identified in Figure 12) from
the fan adapter.
4.
Put the set screw, previously removed, through the two black
neoprene washers and the hook as shown in Figure 14.
Hook
must be installed in same orientation as shown in Figure 14.
Figur
ur
ur
ur
ure 14 - A
e 14 - A
e 14 - A
e 14 - A
e 14 - Assemb
mb
mb
mb
mblin
lin
lin
lin
ling t
g t
g t
g t
g the s
e s
e s
e s
e set s
t s
t s
t s
t screw f
w f
w f
w f
w for l
r l
r l
r l
r low p
w p
w p
w p
w profil
il
il
il
ile
assemb
mb
mb
mb
mbly
5.
Reassemble the set screw to the adapter as shown in Figure 14.
NOTE:
The rubber washers should be tight enough to keep
the hook standing straight up, but the set screw should not be
completely tighten as to keep the hook from being able to
swing.
Slots
Arrows for Orienting
on Angled Ceiling
Ceiling Joist
2 x 4 Brace
Ceiling
Ceiling Plate
Flat Washer
Outlet Box
3” Wood Screw
Hanger Ball/
Downrod Assembly
Canopy
Canopy Trim Ring
Set Screw
Hanger Ball/
Downrod
Assembly
Screw on the Hanger Ball
Black Neoprene
Washer
Hook
Set Screw