Husqvarna 115iPT4 Owner Manual - Page 13

Maintenance

Get Husqvarna 115iPT4 PDF manuals and user guides View all Husqvarna 115iPT4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

1. Push the SavE button. The LED comes on to show that the function is on. 2. Push and hold the stop button until the green LED light goes off. 3. Remove the battery from the product. Push the 2 release buttons and pull out the battery. 2. Push the SavE button again to stop the SavE function. To stop the product 1. Release the power trigger. Introduction Maintenance Maintenance schedule WARNING: Read and understand the safety chapter before you do maintenance work on the product. WARNING: Remove the battery before you do maintenance. WARNING: Remove the battery before you do maintenance on the product. The following is a list of the maintenance steps that you must do on the product. Refer to the tasks in the maintenance chapter for more information. Maintenance Clean the external parts of the product with a dry cloth. Do not use water. Make sure that the start and stop button works correctly and are not damaged. Make sure that the power trigger and the power trigger lockout function correctly from a safety point of view. Make sure that all controls work and are not damaged. Keep the handles dry and clean. Makes sure that that there is no oil and grease on the handles. Make sure that the saw chain cover is not damaged. Replace the saw chain cover if it is damaged. Make sure that the screws and nuts are tight. Clean the oil tank cap Make sure that the battery release buttons on the battery works and locks the battery in the product. Daily X X X X X X X X X Weekly Monthly 707 - 003 - 04.03.2019 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
1.
Push the SavE button. The LED comes on to show
that the function is on.
2.
Push the SavE button again to stop the SavE
function.
To stop the product
1.
Release the power trigger.
2.
Push and hold the stop button until the green LED
light goes off.
3.
Remove the battery from the product. Push the 2
release buttons and pull out the battery.
Maintenance
Introduction
WARNING:
Read and understand the safety
chapter before you do maintenance work on
the product.
WARNING:
Remove the battery before you
do maintenance on the product.
Maintenance schedule
WARNING:
Remove the battery before you
do maintenance.
The following is a list of the maintenance steps that you
must do on the product. Refer to the tasks in the
maintenance chapter for more information.
Maintenance
Daily
Weekly
Monthly
Clean the external parts of the product with a
dry cloth. Do not use water.
X
Make sure that the start and stop button
works correctly and are not damaged.
X
Make sure that the power trigger and the
power trigger lockout function correctly from
a safety point of view.
X
Make sure that all controls work and are not
damaged.
X
Keep the handles dry and clean. Makes sure
that that there is no oil and grease on the
handles.
X
Make sure that the saw chain cover is not
damaged. Replace the saw chain cover if it is
damaged.
X
Make sure that the screws and nuts are tight.
X
Clean the oil tank cap
X
Make sure that the battery release buttons
on the battery works and locks the battery in
the product.
X
707 - 003 - 04.03.2019
13