Husqvarna 129LDX Operation Manual - Page 13

Starting And Stopping

Get Husqvarna 129LDX PDF manuals and user guides View all Husqvarna 129LDX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

STARTING AND STOPPING Check before starting Set the choke control in the choke position. • Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard or with a defective guard. • All covers must be correctly fitted and undamaged before you start the machine. Starting and stopping ! WARNING! When the engine is started with the choke in choke position the cutting attachment will start to rotate immediately. 3. Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Never wrap the starter cord around your hand WARNING! The complete clutch cover and ! shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. Always move the machine away from the refueling area and source before starting. Place the machine on a flat surface. Ensure the cutting attachment cannot come into contact with any object. Make sure no unauthorized persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 50 feet (15 m). Starting Press the air purge 10 times until fuel begins to fill the bulb. The bulb need not be completely filled. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. Repeat pulling the cord until the engine attempts to start or until you have pulled the cord 3 times in total. 4. Push the choke lever down to the run position. 5. Pull the cord until the engine starts. 6. Once the engine starts, allow the engine to warm up for 30 seconds before squeezing the trigger. 1. Primer bulb: Press the air purge 10 times until fuel begins to fill bulb. The bulb need not be completely 2. Pull the cord until the engine starts or until you have pulled the cord 3 times in total. Stopping Stop the engine by switching off the ignition. CAUTION! The stop switch automatically returns to the start position. In order to prevent unintentional starting, the spark plug cap must be removed from the spark plug when assembling, checking and/or performing maintenance. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
STARTING AND STOPPING
Check before starting
•
Check that the trimmer head and trimmer guard are
not damaged or cracked. Replace the trimmer head or
trimmer guard if they have been exposed to impact or
are cracked.
•
Never use the machine without a guard or with a
defective guard.
•
All covers must be correctly fitted and undamaged
before you start the machine.
Starting and stopping
Starting
Press the air purge 10 times until fuel
begins to fill the bulb. The bulb need not be completely
filled.
Set the choke control in the choke position.
3.
Hold the body of the machine on the ground using your
left hand (CAUTION! Not with your foot!). Grip the starter
handle, slowly pull out the cord with your right hand until
you feel some resistance (the starter pawls grip), now
quickly and powerfully pull the cord.
Never wrap the
starter cord around your hand
CAUTION!
!
WARNING! The complete clutch cover and
shaft must be fitted before the machine is
started, otherwise the clutch can come
loose and cause personal injury.
Always move the machine away from the
refueling area and source before starting.
Place the machine on a flat surface. Ensure
the cutting attachment cannot come into
contact with any object.
Make sure no unauthorized persons are
in the working area, otherwise there is a
risk of serious personal injury. The safety
distance is 50 feet (15 m).
!
WARNING! When the engine is started
with the choke in choke position the
cutting attachment will start to rotate
immediately.
Repeat pulling the cord until the engine attempts to
1. Primer bulb: Press the air purge 10 times until fuel
2. Pull the cord until the engine starts or until you have
pulled the cord 3 times in total.
begins to fill bulb. The bulb need not be completely
start or until you have pulled the cord 3 times in total.
°±²³´µ¶·¸
¹±²º»¼½·»²¾¿À¾¸
Do not pull the starter cord all the way out and
do not let go of the starter handle when the cord is fully
extended. This can damage the machine.
Push the choke lever down to the run position.
Pull the cord until the engine starts.
Once the engine starts, allow the engine to warm up for
30 seconds before squeezing the trigger.
4.
5.
6.
Stopping
Stop the engine by switching off the ignition.
CAUTION!
The stop switch automatically returns to the
start position. In order to prevent unintentional starting,
the spark plug cap must be removed from the spark plug
when assembling, checking and/or performing
maintenance.
13