Husqvarna 359 Operation Manual - Page 2

Key To Symbols - chain

Page 2 highlights

KEY TO SYMBOLS Symbols on the machine: WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator's manual carefully and make sure you understand the instructions before using the machine. Always wear: • Approved protective helmet • Approved hearing protection • Protective goggles or a visor Both of the operator′s hands must be used to operate the chain saw. Refuelling. Filing with oil and adjusting oil flow. The chain brake must be engaged when the chain saw is started. If your machine bears this symbol it is equipped with a catalytic converter. You will find the following labels on your chain saw: Never operate a chain saw holding it with one hand only. Never let the guide bar tip come in contact with any object. WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, and cause a lightning fast reverse reaction, kicking the guide bar up and towards the operator. May cause serious personal injury. Other symbols/decals on the machine refer to special certification requirements for certain markets. Symbols in the operator's manual: Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance. Always wear approved protective gloves. Regular cleaning is required. Visual check. EPA I EPA II The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours. Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual. Protective goggles or a visor must be worn. 2 - English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

2 –
English
KEY TO SYMBOLS
Symbols on the machine:
WARNING! Chain saws can be dangerous!
Careless or improper use can result in
serious or fatal injury to the operator or
others.
Please read the operator’s manual carefully
and make sure you understand the
instructions before using the machine.
Always wear:
Approved protective helmet
Approved hearing protection
Protective goggles or a visor
Both of the operator
s hands must be used to
operate the chain saw.
Never operate a chain saw holding it with one
hand only.
Never let the guide bar tip come in contact with
any object.
WARNING! Kickback may occur when the
nose or tip of the guide bar touches an object,
and cause a lightning fast reverse reaction,
kicking the guide bar up and towards the
operator. May cause serious personal injury.
Other symbols/decals on the machine refer to special
certification requirements for certain markets.
Symbols in the operator’s manual:
Switch off the engine by moving the stop
switch to the STOP position before carrying
out any checks or maintenance.
Always wear approved protective gloves.
Regular cleaning is required.
Visual check.
Protective goggles or a visor must be worn.
Refuelling.
Filing with oil and adjusting oil flow.
The chain brake must be engaged when
the chain saw is started.
If your machine bears this symbol it is
equipped with a catalytic converter.
You will find the following labels on your chain saw:
EPA I
EPA II
The Emissions Compliance Period referred to on the
Emission Compliance label indicates the number of operating
hours for which the engine has been shown to meet Federal
emissions requirements. Category C = 50 hours, B = 125
hours, and A = 300 hours.
Maintenance, replacement, or repair of the emission control
devices and system may be performed by any nonroad
engine repair establishment or individual.