Husqvarna 359 Operation Manual - Page 38
Technical Data - xp
View all Husqvarna 359 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 38 highlights
TECHNICAL DATA Technical data Engine Cylinder displacement, cu.in/cm3 Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Power, kW/ rpm Ignition system Manufacturer of ignition system Type of ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system Manufacturer of carburetor Carburetor type Fuel tank capacity, US pint/litre Oil pump capacity at 9,000 rpm, ml/min Oil tank capacity, US pint/litre Type of oil pump Weight Chain saw without bar or chain, empty tanks, lb/kg Chain/bar Standard bar length, inch/cm Recommended bar lengths, inch/cm Usable cutting length, inches/cm Chain speed at max. power, m/sec Pitch, inch/mm Thickness of drive links, inch/mm Number of teeth on drive sprocket 357XP 359 3,45/56,5 1,81/46 1,34/34,0 2700 3,2/9600 3,60/59,0 1,85/47 1,34/34,0 2700 2,9/9000 SEM CD NGK BPMR 7A/Champion RCJ 7Y 0,02/0,5 SEM CD NGK BPMR 7A/Champion RCJ 7Y 0,02/0,5 Walbro HDA 199/191 1,43/0,68 6-17 0,80/0,38 Automatic Walbro HDA 199/191 1,43/0,68 6-17 0,80/0,38 Automatic 12,1/5,5: 357 XP, 357 XP E-tech 12,1/5,5: 359, 359 E-tech 12,3/5,6: 357 XPG, 357 XPG E-tech 12,3/5,6: 359 G, 359 G E-tech 15"/38 13-24"/33-61 12-23"/31-58 21,4 0,325/8,25 3/8" /9,52 0,050/1,3 0,058/1,5 7 15"/38 13-24"/33-61 12-23"/31-58 20,0 0,325/8,25 3/8" /9,52 0,050/1,3 0,058/1,5 7 Recommended original and replacement bar and chain combinations Following is a list of recommended cutting equipment for the Husqvarna chain saw models 357XP and 359. The combinations of power head, bar and chain have been tested and found to be in accordance with the kickback and vibration requirements of ANSI B 175.1-2000. The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a hard nose. The following list is the chain saw manufacturers recommendations. There may be other combinations available, which will also achieve kickback reduction. As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of sprocket teeth may be considered to have equivalent kickback energy. A hard nose bar having the same length and nose radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar. Bar and chain combinations Chain saw models Husqvarna 357XP and 359 met the kickback performance requirements of ANSI B 175.1-2000 when tested with the combinations of bars and saw chains listed below. The saw chain Husqvarna H30 is also classified as a low kickback saw chain since it met the requirements for low kickback saw chain outlined in ANSI B 175.1-2000. We recommend to use only the listed combinations of bars and chains for chain saw models Husqvarna 357XP and 359. Other chain saw models may not meet the kickback requirements when equipped with the listed bar and chain combinations. 38 - English