Husqvarna 365 Operation Manual - Page 34

TECHNICAL DATA 362XP Engine Cylinder volume, cu.in/cm3 Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Power, kW/ rpm 3,8/62,4 1,85/47 1,4/36 2 700 3,4/ 9 600 365 4,0/65,1 1,89/48 1,4/36 2 700 3,4/ 9 300 371XP 4,3/70,7 1,97/50 1,4/36 2 700 3,9/ 9 600 Recommended original and replacement bar and chain combinations These Husqvarna saw models are in the ANSI category of saws above 3,8 cu. in. and are not required to comply with low kickback performance requirements. However, for these models we recommend the following cutting equipment. Ignition system Manufacture FHP Type of ignition system CD Spark plug Champion RCJ7Y Electrode gap, inch/mm 0,02/0,5 FHP CD Champion RCJ7Y 0,02/0,5 FHP CD Champion RCJ7Y 0,02/0,5 Fuel and lubrication system Manufacturer Walbro Carburetor type HD6 Fuel capacity, US pint/litre 1,63/0,77 Oil pump capacity at 8500 rpm, ml/min 4-20 Oil capacity, US pint/litre 0,89/0,42 Type of oil pump Automatic Zama C3M-EL8 1,63/0,77 4-20 0,89/0,42 Automatic Walbro HD12 1,63/0,77 4-20 0,89/0,42 Automatic Weight Without bar and chain, Lbs/kg Chain/bar Recommended bar lengths, inches/cm Usable cutting length, inches/cm Chain speed at max. power, m/sec 13,2/6,0 XPG:13,7/6,2 13-24"/33-61 12-23"/31-58 21,4 13,2/6,0 13,0/5,9 XPG:13,4/6,1 15-28"/38-71 15-28"/38-71 14-27"/35-69 14-27"/35-69 20,7 21,4 Pitch, inch/mm Thickness of drive link, inch/mm Number of teeth on drive sprocket 3/8"/ 9,52 0,325"/ 8,25 0,058"/1,5 7 3/8"/ 9,52 0,058"/1,5 0,050"/1,3 7 3/8"/ 9,52 0,058"/1,5 0,050"/1,3 7 Model 362 Guide bar Length Pitch Max nose inch inch radius 15 0,325 10T 16 0,325 10T 18 0,325 10T 20 0,325 12T 15-24 3/8 11T Saw chain Husqvarna H25 / H21 or Oregon 21VB / 21LP Husqvarna H42 / EM S48 or Oregon 73VL / 73LG / 73L Model 365 and 371 Guide bar Length Pitch Max nose inch inch radius Saw chain 15-28 3/8 11T Husqvarna H42 / EM S48 or Oregon 73VL / 73LG / 73L Note: For the chains above you are free to choose between 0,050" and 0,058" gauge drive link for the corresponding bar, see the table below. 0,058"/1,5 mm H25 H21 H42 EM S48 21VB 21LP 73VL 73LG 73L 0,050"/1,3 mm - -- - 20VB 20LP 72VL 72LG 72L The combinations of powerhead, bar and chain have been investigated in accordance with the vibration requirements of ANSI B 175.1-1991. ! WARNING! These models of chain saws are capable of severe kickback that could result in serious injuries to the user. Do not operate these saws unless you have extraordinary cutting needs and experience and specialized training for dealing with kickback. Saws with significantly reduced kickback potential are available. Always use the safest saw and cutting equipment applicable to your cutting need. 34 - English ´*3$G¶54¨