Husqvarna 395 XP G Owners Manual
Husqvarna 395 XP G Manual
 |
View all Husqvarna 395 XP G manuals
Add to My Manuals
Save this manual to your list of manuals |
Husqvarna 395 XP G manual content summary:
- Husqvarna 395 XP G | Owners Manual - Page 1
Operator's manual 395XP 395XPG Please read the operator's manual carefully and make sure you understand the instructions before using the machine. English - Husqvarna 395 XP G | Owners Manual - Page 2
KEY TO SYMBOLS Symbols on the machine: WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator's manual carefully and make sure you understand the instructions before using the machine. Always wear: • - Husqvarna 395 XP G | Owners Manual - Page 3
chain saw: EPA I EPA III The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours. Maintenance, replacement - Husqvarna 395 XP G | Owners Manual - Page 4
Fuel 18 Fueling 19 Fuel safety 19 STARTING AND STOPPING Starting and stopping 20 WORKING TECHNIQUES Before use 22 General working instructions 22 How to avoid kickback 28 MAINTENANCE Carburetor adjustment 30 Checking, maintaining and servicing chain saw safety equipment 31 Muffler 33 - Husqvarna 395 XP G | Owners Manual - Page 5
mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working today. Today Husqvarna is one of the leading a long time. Think of this operator′s manual as a valuable document. By following its′ content (using, service, maintenance etc) the life span and the second - Husqvarna 395 XP G | Owners Manual - Page 6
Husqvarna AB Huskvarna, SWEDEN 22 6 5 4 12 3 12 21 11 20 19 18 17 16 15 14 13 28 7 8 27 9 10 25 23 26 What is what on the chain saw? 1 Cylinder cover 2 Front handle 3 Front hand guard 4 Starter 5 Chain oil tank 6 Starter handle 7 Adjuster screws carburetor 8 Choke control/Start throttle - Husqvarna 395 XP G | Owners Manual - Page 7
in serious personal injury or the death of the operator or others. Your warranty may not cover damage or liability caused by the use of non- authorized accessories or replacement parts. WARNING! A chain saw is a dangerous ! tool if used carelessly or incorrectly and can cause serious, even - Husqvarna 395 XP G | Owners Manual - Page 8
features and their function are explained. For inspection and maintenance see instructions under the heading Checking, maintaining and servicing chain saw safety equipment. See instructions under the heading, What is what?, to find where these parts are located on your machine. The life span of the - Husqvarna 395 XP G | Owners Manual - Page 9
is designed to be activated by the inertia in the kickback direction. • The chain brake must be engaged when the chain saw is started to prevent the saw chain from rotating. • Use the chain brake as a "parking brake" when starting and when moving over short distances, to If the kickback is less - Husqvarna 395 XP G | Owners Manual - Page 10
manual activation of the chain brake impossible. With this type of grip, that is when the left hand is placed so that it cannot affect the movement of the front hand guard, the chain is simple, see instructions under the heading Checking, maintaining and servicing chain saw safety equipment. We - Husqvarna 395 XP G | Owners Manual - Page 11
start a fire. Never start the machine indoors or near combustible material! The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine′s handle unit. The body of the chain saw Never use a saw without a ! saw saw chain - Husqvarna 395 XP G | Owners Manual - Page 12
rotating ! saw chain can cause extremely serious injuries. Some terms that describe the bar and chain To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the - Husqvarna 395 XP G | Owners Manual - Page 13
sharpen cutting teeth you will need a round file and a file gauge. See instructions under the heading Technical data for information on the size of file and gauge that are recommended for the chain fitted to your chain saw. When you sharpen a cutting tooth there are four important factors to remember - Husqvarna 395 XP G | Owners Manual - Page 14
while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar. The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under 14 - English - Husqvarna 395 XP G | Owners Manual - Page 15
is clean. Clean if necessary. Filling with chain oil • All our chain saws have an automatic chain lubrication system. On some models the oil flow long will use more chain oil). Checking chain lubrication • Check the chain lubrication each time you refuel. See instructions under the heading - Husqvarna 395 XP G | Owners Manual - Page 16
has worn down to only 5/32 inch (4 mm) the chain must be replaced. Bar Check regularly: WARNING! Most chain saw accidents ! happen when the chain touches the operator. Wear personal protective equipment. See instructions under the heading "Personal protective equipment". Do not tackle any - Husqvarna 395 XP G | Owners Manual - Page 17
adjuster pin in the hole in the bar. Check that the drive links of the chain fit correctly over the drive sprocket and that the chain is Note: If clutch cover is difficult to remove, replace bar nuts, engage brake and rerelease (an audible click will be heard if released properly). English - 17 - Husqvarna 395 XP G | Owners Manual - Page 18
green fuel cap on saws fitted with catalytic of fuel (see instructions under the heading Carburetor results and performance use HUSQVARNA two-stroke engine oil, container intended for fuel. • Always start by filling half the amount of cleaned. Chain oil • We recommend the use of special oil (chain oil) - Husqvarna 395 XP G | Owners Manual - Page 19
starting. Clean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced and storage • Always store the chain saw and fuel so that there is instructions under the heading Maintenance schedule. Ensure the machine is cleaned and that a complete service - Husqvarna 395 XP G | Owners Manual - Page 20
and stopping WARNING! Note the following before ! starting: Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries. Warm engine Use the same procedure as for starting a cold engine but without setting the - Husqvarna 395 XP G | Owners Manual - Page 21
mist and dust from sawdust can represent a health risk. • Never start a chain saw unless the bar, chain and all covers are fitted correctly. See instructions under the heading Assembly. Without a bar and chain attached to the chain saw the clutch can come loose and cause serious injury. • Always - Husqvarna 395 XP G | Owners Manual - Page 22
seek expert advice. Contact your chain saw dealer, service agent or an experienced chain saw user. Do not attempt any task that you are not sure you can handle! Before using a chain saw you must understand the effects of kickback and how to avoid them. See instructions under the heading How to avoid - Husqvarna 395 XP G | Owners Manual - Page 23
mild, but it can sometimes be very sudden and violent. 2 Always hold the chain saw firmly with your right hand on the rear handle and your left hand on handed. This grip minimizes the effect of kickback and lets you keep the chain saw under control. Do not let go of the handles! Have control over the - Husqvarna 395 XP G | Owners Manual - Page 24
other insecure support. Basic cutting technique WARNING! Never use a chain saw by ! holding it with one hand. A chain saw is not instructions on sharpening and maintaining your bar and chain. When you replace the bar and chain use only combinations that are recommended by us. See instructions - Husqvarna 395 XP G | Owners Manual - Page 25
chain saw free. If you do you may be injured by the chain when the chain saw suddenly breaks free. Use a lever to open up the cut and free the chain saw. The following instructions working. The log is supported at both ends. There is a high risk that the chain will jam. Start by cutting from above - Husqvarna 395 XP G | Owners Manual - Page 26
chain saws should not fell trees. Do not attempt any task beyond your experience level! there is high accident risk. See instructions • Wind direction • Arrangement of branches • Weight of snow • Obstacles within the reach of the path of retreat when the tree starts to fall. Your path of retreat - Husqvarna 395 XP G | Owners Manual - Page 27
placed. When the felling cut and directional cut are complete the tree should start to fall by itself or with the aid of a felling wedge or cutting strokes. See instructions under the heading Technical data section to find out which lengths of bar are recommended for your saw. Felling cut The - Husqvarna 395 XP G | Owners Manual - Page 28
The word kickback is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the safely. In complicated situations the only safe method is to put aside your chain saw and use a winch. General advice: Position yourself so that you will be - Husqvarna 395 XP G | Owners Manual - Page 29
the kickback zone of the guide bar. Be extremely cautious and avoid contacting the log, chain saw for maximum control. If possible, let the weight of the chain saw rest on the trunk. Keep the trunk between you and the chain saw as you move along the trunk. Cutting the trunk into logs See instructions - Husqvarna 395 XP G | Owners Manual - Page 30
of a 1/2 turn. L H 1/2 1/2 Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. Function, Basic settings, Fine adjustment WARNING! Do not start the chain saw ! unless the bar, chain and clutch cover (chain brake) are fitted, otherwise the - Husqvarna 395 XP G | Owners Manual - Page 31
It should also be good margin to the rpm when the chain starts to rotate. WARNING! Contact your servicing ! dealer, if the idle speed setting cannot be adjusted so that the chain stops at idle. Do not use the chain saw until it has been properly adjusted or repaired. Checking, maintaining and - Husqvarna 395 XP G | Owners Manual - Page 32
its original position when you release it. Checking the brake trigger Place the chain saw on firm ground and start it. Make sure the chain does not touch the ground or any other object. See the instructions under the heading Start and stop. • Check that the throttle control and throttle lockout move - Husqvarna 395 XP G | Owners Manual - Page 33
and is firmly attached to the body of the chain saw. Start the engine and make sure the engine stops when you will cause the engine to overheat and may lead to serious damage. Note! The screen must be replaced if it is damaged. If the screen is blocked the machine will overheat and this will cause - Husqvarna 395 XP G | Owners Manual - Page 34
, pop out and cause personal injury. Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective housing and the starter • Lift up the starter pulley. See instructions under the heading Changing a broken or worn starter cord. Remember that - Husqvarna 395 XP G | Owners Manual - Page 35
order to avoid: • Carburettor malfunctions • Starting problems • Loss of engine power • Unnecessary wear to engine parts • Excessive fuel consumption. • Remove therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced. A HUSQVARNA chain saw can be - Husqvarna 395 XP G | Owners Manual - Page 36
bearing grease or engine oil. See instructions under the heading Cutting equipment. To consists of: 1 Air intake on the starter. 2 Air guide plate. 3 Fins on the flywheel. 4 Cooling fi closed position. These recommendations apply to Husqvarna's chain oil, for other chain oils increase the oil flow by - Husqvarna 395 XP G | Owners Manual - Page 37
problems can occur when using the machine in the cold and snowy conditions caused by: • Too low engine temperature. • Icing of the air filter and carburetor. Special measures are therefore often required: • Partly electricity from a generator built into the chain saw. CAUTION! When the plug is fitted - Husqvarna 395 XP G | Owners Manual - Page 38
that there are no fuel leaks from the engine, tank or fuel lines. On chain saws with a catalytic converter, check the cooling system daily. Monthly maintenance Check the brake band on the chain brake for wear. Replace when less than 0.024 inch (0.6 mm) remains at the most worn point. Check the - Husqvarna 395 XP G | Owners Manual - Page 39
, US pint/litre Oil pump capacity at 8,500 rpm, ml/min Oil tank capacity, US pint/litre Type of oil pump Weight Chain saw without bar or chain, empty tanks, lb/kg Chain/bar Recommended bar lengths, inch/cm Usable cutting length, inches/cm Pitch, inch/mm Thickness of drive links, inch/mm Drive - Husqvarna 395 XP G | Owners Manual - Page 40
TECHNICAL DATA Recommended original and replacement bar and chain combinations The Husqvarna 395XP is in the ANSI category of saws above 3,8 cu. in. and is not required to comply with low kickback performance requirements. However, for this model we recommend the following cutting equipment. - Husqvarna 395 XP G | Owners Manual - Page 41
-487-5963. WHERE TO GET WARRANTY SERVICE Warranty services or repairs shall be provided at all Husqvarna Forest & Garden authorized servicing dealers. MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS Any Husqvarna Forest & Garden approved replacement part used in the performance of any - Husqvarna 395 XP G | Owners Manual - Page 42
FEDERAL EMISSION CONTROL WARRANTY STATEMENT EMISSION CONTROL WARRANTY PARTS LIST 1 Carburetor and internal parts 2 Intake pipe, airfilter holder and carburetor bolts. 3 Airfilter and fuelfilter covered up for the performance of all required maintenance, as defined in the operator's manual. 42 - English - Husqvarna 395 XP G | Owners Manual - Page 43
path from the falling tree. Keep all parts of your body away from the saw chain when the engine is running. Before you start the engine, make sure that the saw chain is not contacting anything. Carry the chain saw with the engine stopped, the guide bar and saw chain to the rear, and the muffler - Husqvarna 395 XP G | Owners Manual - Page 44
The engine exhaust from this product contains chemical known to the State of California to cause cancer, birth defects or other reproductive harm. Original instructions 1153177-95 ´´®®zz++UU11oo¶¶55®®¨¨ 2010-04-19
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
 |
 |
English
395XP
395XPG
Oper
ator’s manual
Please r
ead the operator’s manual carefully and make sure you understand the instructions before using the machine.