Husqvarna 465 Rancher Operation Manual - Page 40

TECHNICAL DATA Technical data 455 Rancher II 455e Rancher II 455e Rancher II TrioBrake 465 Rancher II Engine Cylinder displacement, cu.in/cm3 3,38/55,5 3,38/55,5 3,38/55,5 3.91/64,1 Cylinder bore, inch/mm 1.85/47 1.85/47 1.85/47 1.93/49 Stroke, inch/mm 1,26/32 1,26/32 1,26/32 2.07/34 Idle speed, rpm 2700 2700 2700 2700 Power, kW/hp @ rpm 2,6/3,5 @ 9000 2,6/3,5 @ 9000 2,6/3,5 @ 9000 3,2/4.4 @ 9600 Emissions Durability Period according to California Air Resources Board, h. 300 300 300 300 Ignition system Spark plug NGK BPMR 7A NGK BPMR 7A NGK BPMR 7A NGK BPMR 7A Electrode gap, inch/mm 0.02/0,5 0.02/0,5 0.02/0,5 0.02/0,5 Fuel and lubrication system Fuel tank capacity, US pint/liter 0.93/0,44 0.93/0,44 0.93/0,44 0.93/0,44 Oil pump capacity at 9,000 rpm, ml/min 6-17 6-17 6-17 6-17 Oil tank capacity, US pint/liter 0.68/0,32 0.68/0,32 0.68/0,32 0.68/0,32 Type of oil pump Adjustable Adjustable Adjustable Adjustable Weight Chain saw without bar or chain, empty tanks, lb/kg 13,0/5,9 13,2/6,0 13,6/6,2 13,4/6,1 Chain/bar Standard bar length, inch/cm 15/38 15/38 15/38 18/46 Recommended bar lengths, inch/cm 15-20"/38-51 15-20"/38-51 15-20"/38-51 15-28"/38-71 Usable cutting length, inches/cm 14-19"/36-49 14-19"/36-49 14-19"/36-49 14-27"/35-68 Pitch, inch/mm 0.325/8,25 0.325/8,25 0.325/8,25 3/8" /9,52 Thickness of drive links, inch/mm 0.050/1,3 0.050/1,3 0.050/1,3 0.058/1,5 0.058/1,5 0.058/1,5 0.058/1,5 Drive sprocket type/teeth Spur/7 Spur/7 Spur/7 Rim/7 Chain speed at 133% of maximum engine power speed, ft/s / m/s. 87.3/26,6 87.3/26,6 87.3/26,6 93.5/28,5 Recommended cutting equipment for USA Following is a list of recommended cutting equipment for Husqvarna chain saw models 455 Rancher II, 455e Rancher II, 455e Rancher II TrioBrake and 465 Rancher II. These chain saw models equipped with either of the listed guide bar and saw chain combination(s), fulfills the requirements according to ANSI B175.1-2012 (Gasoline Powered Chain Saws - Safety Requirements). Chain saw models Husqvarna 455 Rancher II, 455e Rancher II, 455e Rancher II TrioBrake and 465 Rancher II met the kickback performance requirements of ANSI B175.1-2012 when tested with the combinations of bars and saw chains listed below. The saw chains Husqvarna H80 and H81 are also classified as low kickback saw chains since they met the requirements for low kickback saw chains outlined in ANSI B175.1-2012. We recommend to use only the listed combinations of bars and chains for chain saw models Husqvarna 455 Rancher II, 455e Rancher II, 455e Rancher II TrioBrake and 465 Rancher II. Other chain saw models may not meet the kickback requirements when equipped with the listed guide bar and saw chain combinations. Recommended cutting equipment for Canada Following is a list of recommended cutting equipment for the Husqvarna chain saw models 455 Rancher II, 455e Rancher II, 455e Rancher II TrioBrake, 460 Rancher II and 465 Rancher II. The listed combination(s) of powerhead, guide bar and saw chain meet all requirements outlined in Canadian Standards Assosiation Z62.1-11 (Chain Saws) and Z62.3-11 (Chain Saw Kickback). Furthermore the saw chains Husqvarna H80 and H81 are evaluated and listed as a Type C Low Kickback Saw Chain according to the provisions in Z62.3-11. 40 - English