Husqvarna 522HDR75S Owner Manual - Page 10

To stop the product, To operate the product, Maintenance, Introduction, Maintenance schedule

Get Husqvarna 522HDR75S PDF manuals and user guides View all Husqvarna 522HDR75S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

2. Pull the starter rope handle slowly with your right hand until you feel some resistance, then pull the starter rope handle quickly and with force. Continue until the engine starts. Note: For more information about how to start the product, refer to To start the product with a cold engine on page 9. To stop the product • Move the stop switch to the stop position to stop the engine. WARNING: Make sure that the front of the cutting equipment does not touch the ground. 2. Adjust the speed to align with the work load. 3. Hold the product near your body for a stable work position. 4. Be careful and operate the product slowly. CAUTION: The stop switch automatically goes back to run position. To operate the product 1. Start near the ground and move the product up along the hedge when you cut the sides. Make sure that the body of the product does not touch the hedge. Maintenance Introduction WARNING: Read and understand the safety chapter before you do maintenance on the product. Maintenance schedule Maintenance Before After 40 After 100 operation h h Clean the external surface. After each operation. Clean the muffler, exhaust pipe and engine from leaves, dirt and unwanted lubricant. After each operation. Make sure that the cutting attachment does not move at idle speed. X Do a check of the stop switch. X 10 904 - 003 - 19.03.2019

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
2.
Pull the starter rope handle slowly with your right
hand until you feel some resistance, then pull the
starter rope handle quickly and with force. Continue
until the engine starts.
Note:
For more information about how to start the
product, refer to
To start the product with a cold engine
on page 9
.
To stop the product
•
Move the stop switch to the stop position to stop the
engine.
CAUTION:
The stop switch automatically
goes back to run position.
To operate the product
1.
Start near the ground and move the product up
along the hedge when you cut the sides. Make sure
that the body of the product does not touch the
hedge.
WARNING:
Make sure that the front of
the cutting equipment does not touch the
ground.
2.
Adjust the speed to align with the work load.
3.
Hold the product near your body for a stable work
position.
4.
Be careful and operate the product slowly.
Maintenance
Introduction
WARNING:
Read and understand the safety
chapter before you do maintenance on the
product.
Maintenance schedule
Maintenance
Before
operation
After 40
h
After 100
h
Clean the external surface.
After each operation.
Clean the muffler, exhaust pipe and engine from leaves, dirt and unwanted lubri-
cant.
After each operation.
Make sure that the cutting attachment does not move at idle speed.
X
Do a check of the stop switch.
X
10
904 - 003 - 19.03.2019