Husqvarna 530iPT5 Owner Manual - Page 22

To clean the product, the battery and the battery charger, Troubleshooting, Keypad, Battery

Page 22 highlights

5. Remove the chain drive sprocket (E). B D A E C 6. Install a new chain drive sprocket. To clean the product, the battery and the battery charger 1. Clean the product with a dry cloth after use. 2. Clean the battery and battery charger with a dry cloth. Keep the battery guide tracks clean. 3. Make sure that the terminals on the battery and the battery charger are clean before use. 4. Clean around the oil tank cap with a brush. 5. Clean the inner surface of the protective cover with a brush. Troubleshooting Keypad Problem Possible faults Possible solution Green start LED flashes. Low battery voltage. Charge the battery. Red error LED flash- Overload. es. The cutting attachment is blocked. stop the product. Remove the battery. Clean the cutting attachment from unwanted materials. Loosen the chain. Temperature deviation. Let the product become cool. The power trigger and the start button are pushed at the same time. Release the power trigger and push the start button. The product does not Dirt in the battery connectors. start. Clean the battery connectors with compressed air or a soft brush. Red error LED comes on. It is necessary to do servicing on the product. Speak to your servicing dealer. Battery LED display Green activate LED flashing Error LED flashing Error LED is lit Possible faults Possible action Low battery voltage. Charge the battery. The battery is discharged. Charge the battery. Temperature deviation. Use the battery in surroundings where temperatures are between -10°C (14°F) and 40°C (104°F). Cell difference is too much (1V). Contact your servicing agent. 22 783 - 003 - 28.05.2019

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80

5.
Remove the chain drive sprocket (E).
A
B
C
E
D
6.
Install a new chain drive sprocket.
To clean the product, the battery and
the battery charger
1.
Clean the product with a dry cloth after use.
2.
Clean the battery and battery charger with a dry
cloth. Keep the battery guide tracks clean.
3.
Make sure that the terminals on the battery and the
battery charger are clean before use.
4.
Clean around the oil tank cap with a brush.
5.
Clean the inner surface of the protective cover with a
brush.
Troubleshooting
Keypad
Problem
Possible faults
Possible solution
Green start LED
flashes.
Low battery voltage.
Charge the battery.
Red error LED flash-
es.
Overload.
The cutting attachment is blocked. stop the
product. Remove the battery. Clean the cut-
ting attachment from unwanted materials.
Loosen the chain.
Temperature deviation.
Let the product become cool.
The power trigger and the start button are
pushed at the same time.
Release the power trigger and push the start
button.
The product does not
start.
Dirt in the battery connectors.
Clean the battery connectors with com-
pressed air or a soft brush.
Red error LED
comes on.
It is necessary to do servicing on the product.
Speak to your servicing dealer.
Battery
LED display
Possible faults
Possible action
Green activate LED flashing
Low battery voltage.
Charge the battery.
Error LED flashing
The battery is discharged.
Charge the battery.
Temperature deviation.
Use the battery in surroundings where tem-
peratures are between -10°C (14°F) and
40°C (104°F).
Error LED is lit
Cell difference is too much (1V).
Contact your servicing agent.
22
783 - 003 - 28.05.2019