Home » Husqvarna Manuals » Lawn & Garden » Husqvarna 535LST » Manual Viewer

Husqvarna 535LST Owner Manual - Page 9

Fuel Safety, Safety instructions for maintenance, Assembly, Introduction

Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

a) Clean the spark arrester screen if it is blocked. A blocked mesh will make the engine overheated which can cause serious damage. b) Make sure that the spark arrestor mesh is attached correct. Fuel Safety WARNING: Read the warning instructions that follow before you use the product. • Never start the product if you spill fuel on it. Wipe the spillage of and allow remaining fuel to evaporate. • Never start the product if you spill fuel on yourself or your clothes. Change your clothes and wash any part of your body that has come in contact with fuel. Use soap and water. • Never start the product if the product is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines. • Always put the product on a flat surface and make sure the cutting attachment cannot come in contact with any object while you add fuel. • Take care when handling fuel. Bear in mind the risk off fire, explosion and inhaling fumes. • Observe caution when handling fuel and make sure there is adequate ventilation. Fuel and fuel fumes are highly inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin. • Mix and pour fuel outdoors, where there are no sparks or flames. • Do not smoke or place hot objects near fuel. • Always stop the engine and let it cool off for a few minutes before you refuel. • Open the fuel cap slowly so that any excess pressure is released gently when you refuel. • Tighten the fuel cap carefully after you refueled. • Clean the area around the fuel cap. Contamination in the tank can cause operating problems. • Always move the product 3m (10ft) or further from the refuelling area and source before starting. Safety instructions for maintenance WARNING: Always stop the engine before you do any work on the cutting attachment. The cutting attachment continues to rotate even after the throttle has been released. Ensure that the cutting attachment has stopped completely and disconnect the spark plug before you start to work on it. WARNING: Make sure that the trimmer cord is wound tightly and evenly around the drum, otherwise the product will generate harmful vibration. • Only use cutting attachments with the guards we recommend. Refer to Accessories on page 19. WARNING: A faulty cutting attachment may increase the risk of accidents. Assembly Introduction WARNING: Before you assemble the product, you must read and understand the safety chapter. WARNING: Remove the spark plug cable from the spark plug before you assemble the product. 1011 - 005 - 9

Section	Page
Contents	2
Introduction	2
Intended use	2
Product overview	2
Symbols on the product	3
EPA III	3
California Proposition 65	4
Safety	4
Safety definitions	4
General safety instructions	4
Safety instructions for operation	4
Personal protective equipment	5
Safety devices on the product	6
To do a check of the throttle trigger lockout	6
To do a check of the stop switch	7
To do a check of the cutting attachment guard	7
To do a check of the vibration damping system	8
To do a check of the muffler	8
Fuel Safety	9
Safety instructions for maintenance	9
Assembly	9
Introduction	9
To assemble the loop handle	10
To assemble the cutting attachment guard and trimmer head	10
To disassemble the cutting attachment guard and trimmer head	10
Operation	11
Fuel	11
Gasoline	11
Husqvarna alkylate fuel	11
Two-stroke oil	11
To mix gasoline and two-stroke oil	11
To fill the fuel tank	12
Before you operate the product	12
To prepare the product for start	12
To start the product	13
About the surface	13
To stop the product	13
Grass trimming with a trimmer head	13
To trim the grass	13
To cut the grass	14
To sweep the grass	14
Maintenance	14
To adjust the idle speed	14
To do maintenance on the muffler	15
To do maintenance on the trimmer head	15
Cooling system	15
To examine the spark plug	16
Air filter	16
To clean the air filter	16
Bevel gear	16
Maintenance schedule	17
Troubleshooting	18
The engine does not start	18
The engine starts but stops again	18
Transportation and storage	18
Transportation and storage	18
Technical data	19
Technical data	19
Accessories	19
Accessories	19
Warranty	20
CALIFORNIA, U.S FEDERAL, AND CANADA EXHAUST AND EVAPORATIVE EMISSIONS CONTROL WARRANTY STATEMENT	20
Contenido	22
Introducción	22
Uso específico	22
Descripción general de la máquina	22
Símbolos en el producto	23
EPA III	23
Propuesta 65 de California	24
Seguridad	24
Definiciones de seguridad	24
Instrucciones generales de seguridad	24
Instrucciones de seguridad para el funcionamiento	24
Equipo de protección personal	26
Dispositivos de seguridad en el producto	26
Comprobación del fiador del acelerador	27
Para comprobar el interruptor de detención	28
Comprobación de la protección del equipo de corte	28
Para comprobar el sistema amortiguador de vibraciones	28
Para comprobar el silenciador	28
Seguridad del combustible	29
Instrucciones de seguridad para el mantenimiento	30
Montaje	30
Introducción	30
Conexión del mango cerrado	30
Para montar la protección del equipo de corte y el cabezal de corte	30
Para desmontar la protección del equipo de corte y el cabezal de corte	31
Funcionamiento	31
Combustible	31
Gasolina	31
Combustible de alquilato Husqvarna	31
Aceite para motores de dos tiempos	32
Para mezclar gasolina y aceite para motores de dos tiempos	32
Para llenar el depósito de combustible	32
Antes de usar el producto	33
Para preparar la máquina para el arranque	33
Para poner en marcha la máquina	33
Información sobre la superficie	34
Para detener la máquina	34
Recorte de césped con cabezal de corte	34
Para recortar el césped	34
Para cortar el césped	34
Para barrer el césped	34
Mantenimiento	35
Para ajustar el régimen de ralentí	35
Para realizar tareas de mantenimiento en el silenciador	35
Para realizar tareas de mantenimiento en el cabezal de corte	36
Sistema refrigerante	36
Para examinar la bujía	36
Filtro de aire	36
Para limpiar el filtro de aire	37
Engranaje angulado	37
Programa de mantenimiento	37
Solución de problemas	38
El motor no arranca	38
El motor arranca, pero se detiene de nuevo.	39
Transporte y almacenamiento	39
Transporte y almacenamiento	39
Datos técnicos	39
Datos técnicos	39
Accesorios	40
Accesorios	40
Garantía	41
DECLARACIÓN DE GARANTÍA DEL CONTROL DE EMISIONES DE VAPORES Y DE ESCAPE CONFORME A LA NORMATIVA DE CALIFORNIA, LA NORMATIVA FEDERAL DE LOS ESTADOS UNIDOS y LA NORMATIVA DE CANADÁ	41
Table des matières	44
Introduction	44
Utilisation prévue	44
Présentation de l’appareil	44
Symboles figurant sur la machine	45
EPA III	45
Proposition 65 de la Californie	46
Sécurité	46
Définitions relatives à la sécurité	46
Consignes générales de sécurité	46
Consignes de sécurité pour l’utilisation	46
Équipement de protection personnelle	48
Dispositifs de sécurité sur l’outil	48
Pour vérifier le verrouillage de la gâchette de l’accélérateur	49
Pour vérifier l’interrupteur d’arrêt	50
Vérification du dispositif de protection de l’outil de coupe	50
Pour vérifier le système antivibrations	50
Pour vérifier le silencieux	51
Sécurité – carburant	51
Consignes de sécurité pour la maintenance	52
Montage	52
Introduction	52
Pour monter le guidon en boucle	52
Pour monter le dispositif de protection de l’outil de coupe et la tête de coupe	53
Pour démonter le dispositif de protection de l’outil de coupe et la tête de coupe	53
Fonctionnement	53
Carburant	53
Essence	53
Carburant alkylat Husqvarna	54
Huile à moteur deux-temps	54
Pour mélanger l’essence et l’huile pour moteur à deux temps	54
Remplissage du réservoir de carburant	55
Avant d’utiliser le produit	55
Pour préparer le produit à des fins de démarrage	55
Mise sous tension de l’appareil	56
À propos de la surface	56
Arrêt de l’appareil	56
Désherbage au moyen d’une tête de coupe	56
Tonte du gazon	56
Pour couper l’herbe	57
Pour balayer l’herbe	57
Entretien	57
Réglage du régime de ralenti	57
Pour entretenir le silencieux	58
Pour entretenir la tête de coupe	58
Système de refroidissement	58
Vérification de la bougie d’allumage	59
Filtre à air	59
Nettoyage du filtre à air	59
Pignon conique	60
Calendrier d’entretien	60
Dépannage	61
Le moteur ne démarre pas.	61
Le moteur démarre mais s’arrête à nouveau	62
Transport et entreposage	62
Transport et entreposage	62
Données techniques	62
Données techniques	62
Accessoires	63
Accessoires	63
Garantie	64

Match case Limit results 1 per page

Clean the spark arrester screen if it is blocked. A

blocked mesh will make the engine overheated

which can cause serious damage.

Make sure that the spark arrestor mesh is

attached correct.

Fuel Safety

WARNING:

Read the warning instructions

that follow before you use the product.

•

Never start the product if you spill fuel on it. Wipe the

spillage of and allow remaining fuel to evaporate.

•

Never start the product if you spill fuel on yourself or

your clothes. Change your clothes and wash any

part of your body that has come in contact with fuel.

Use soap and water.

•

Never start the product if the product is leaking fuel.

Check regularly for leaks from the fuel cap and fuel

lines.

•

Always put the product on a flat surface and make

sure the cutting attachment cannot come in contact

with any object while you add fuel.

•

Take care when handling fuel. Bear in mind the risk

off fire, explosion and inhaling fumes.

•

Observe caution when handling fuel and make sure

there is adequate ventilation. Fuel and fuel fumes

are highly inflammable and can cause serious injury

when inhaled or allowed to come in contact with the

skin.

•

Mix and pour fuel outdoors, where there are no

sparks or flames.

•

Do not smoke or place hot objects near fuel.

•

Always stop the engine and let it cool off for a few

minutes before you refuel.

•

Open the fuel cap slowly so that any excess

pressure is released gently when you refuel.

•

Tighten the fuel cap carefully after you refueled.

•

Clean the area around the fuel cap. Contamination in

the tank can cause operating problems.

•

Always move the product 3m (10ft) or further from

the refuelling area and source before starting.

Safety instructions for maintenance

WARNING:

Always stop the engine before

you do any work on the cutting attachment.

The cutting attachment continues to rotate

even after the throttle has been released.

Ensure that the cutting attachment has

stopped completely and disconnect the

spark plug before you start to work on it.

WARNING:

A faulty cutting attachment may

increase the risk of accidents.

WARNING:

Make sure that the trimmer cord

is wound tightly and evenly around the

drum, otherwise the product will generate

harmful vibration.

•

Only use cutting attachments with the guards we

recommend. Refer to

Accessories on page 19

Assembly

Introduction

WARNING:

Before you assemble the

product, you must read and understand the

safety chapter.

WARNING:

Remove the spark plug cable

from the spark plug before you assemble the

product.

1011 - 005 -