Husqvarna 555 Workshop Manual - Page 43

Vibration damping system

Get Husqvarna 555 PDF manuals and user guides View all Husqvarna 555 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Assembly 1. Thread the throttle cables in the connection M as outlined in figure 55. NOTE! The figure is shown from underneath. 2. Run the fuel hose D through hole K and hoses B and C in hole L. See figure 55. Pull the hoses so that the collars are on each side of the bottom on the carburettor compartment. 3. Tighten the chain catcher in place. 4. Press the movement limiter H into position. See figure 53. 5. Tighten the screws F. See figure 51. 6. Hook on the throttle cable E in the intake bellow. See figure 50. 7. Fit the tank unit. The two short screws are fitted to the bottom of the handle bar. 8. Assemble the carburettor as outlined in "Assembling the carburettor". Assemble the air filter and cylinder cover. Fig 54 7.17 Vibration damping system Dismantling 1. Dismantle the following parts: •Bar and chain. See the Operator's Manual. •Cylinder cover. See the Operator's Manual. •Tank unit and handle. See "Dismantling the tank unit". 2. Dismantle the spring on the handle bar using a 4 mm Allen key (see figure 57). 3. Dismantle the springs on the tank unit using a 4 mm Allen key (tool 502 50 18-01). See figure 57. Fig 55 Cleaning and inspection Clean and inspect all parts. Assembly 1. Fit the springs on the handle bar using a 4 mm Allen key (tool 502 50 18-01). 2. Assemble the following parts: •Tank unit and handle. See "Assembling the tank unit". •Cylinder cover. See the Operator's Manual. •Bar and chain. See the Operator's Manual. Fig 56 Fig 57 Repair Instructions English - 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
English -
43
Assembly
1. Thread the throttle cables in the connection M
as outlined in figure 55. NOTE! The figure is
shown from underneath.
2. Run the fuel hose D through hole K and hoses
B and C in hole L. See figure 55. Pull the hoses
so that the collars are on each side of the bot-
tom on the carburettor compartment.
3. Tighten the chain catcher in place.
4. Press the movement limiter H into position. See
figure 53.
5. Tighten the screws F. See figure 51.
6. Hook on the throttle cable E in the intake bellow.
See figure 50.
7. Fit the tank unit. The two short screws are fitted
to the bottom of the handle bar.
8. Assemble the carburettor as outlined in “Assem-
bling the carburettor”. Assemble the air filter
and cylinder cover.
Repair Instructions
7.17 Vibration damping system
Dismantling
1. Dismantle the following parts:
•Bar and chain. See the Operator’s Manual.
•Cylinder cover. See the Operator’s Manual.
•Tank unit and handle. See “Dismantling the
tank unit”.
2. Dismantle the spring on the handle bar using a
4 mm Allen key (see figure 57).
3. Dismantle the springs on the tank unit using
a 4 mm Allen key (tool 502 50 18-01). See
figure 57.
Cleaning and inspection
Clean and inspect all parts.
Assembly
1. Fit the springs on the handle bar using a 4 mm
Allen key (tool 502 50 18-01).
2. Assemble the following parts:
•Tank unit and handle. See “Assembling the
tank unit”.
•Cylinder cover. See the Operator’s Manual.
•Bar and chain. See the Operator’s Manual.
Fig 55
Fig 54
Fig 56
Fig 57