Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 315X » Manual Viewer

Husqvarna AUTOMOWER 315X Owner Manual - Page 21

Installation of the product, To install the charging station, To install the boundary wire - canada

View all Husqvarna AUTOMOWER 315X manuals

Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

3.4 Installation of the product 3.4.1 To install the charging station WARNING: Obey national regulations about electrical safety. 1. Read and understand the instructions about the charging station. Refer to To examine where to put the charging station on page 16. 2. Put the charging station in the selected area. 3. Connect the low-voltage cable to the charging station. 4. Put the power supply at a minimum height of 30 cm / 12 in. weatherproof with the attachment plug cap inserted or removed. 6. Put the low-voltage cable in the ground with stakes or bury the cable. Refer to To put the wire into position with stakes on page 22 or To bury the boundary wire or the guide wire on page 22. 7. Connect the wires to the charging station. Refer to To install the boundary wire on page 21 and To install the guide wire on page 22. 8. Attach the charging station to the ground with the supplied screws. CAUTION: Do not make new holes in the charging station plate. min 30 cm / 12" CAUTION: The product is only to be used with the power supply unit supplied by Husqvarna. WARNING: Do not put the power supply at a height where there is a risk it can be put in water. Do not put the power supply on the ground. CAUTION: Do not put your feet on the charging station. 3.4.2 To install the boundary wire 1. Put the boundary wire around all of the work area. Start and complete the installation behind the charging station. CAUTION: Do not put unwanted wire in a coil. The coil causes interference with the product. 2. Open the connector and put the boundary wire in the connector. WARNING: Do not encapsulate the power supply. Condensed water can harm the power supply and increase the risk of electrical shock. 5. Connect the power supply cable to a 100-240V outdoor power outlet. WARNING: Applicable to USA/ Canada. If power supply is installed outdoors: Risk of Electric Shock. Install only to a covered Class A GFCI receptacle (RCD) that has an enclosure that is 3. Close the connector with a pair of pliers. 4. Cut the boundary wire 1-2 cm / 0.4-0.8 in. above each connector. 5. Put the right end of boundary wire into the channel with the mark "AR". 6. Put the left end of boundary wire into the channel with the mark "AL". 7. Push the right connector onto the metal pin on the charging station with the mark "AR". 1220 - 001 - 08.07.2019 Installation - 21

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	6
Symbols on the battery	6
Menu structure overview - 1	8
Menu structure overview - 2	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	12
Safety instructions for operation	13
Use	13
Battery safety	14
How to lift and move the product	14
Maintenance	15
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Before the installation of the wires	16
Before the installation of the product	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To set the corridor width of the boundary wire	19
To examine where to put the guide wire	19
To set the corridor width of the guide wire	20
Work area examples	20
Installation of the product	21
To install the charging station	21
To install the boundary wire	21
To install the guide wire	22
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	22
To extend the boundary wire or the guide wire	22
After the installation of the product	23
To do a visual check of the charging station	23
To do the basic settings	23
To do the product settings	23
To get access to the menu	23
To do the timer settings	23
To calculate the timer setting	23
To set the timer	24
To copy the timer setting	24
To reset the timer setting	24
Security level	24
To set the security level	24
To change the PIN-code	25
To change the length of the alarm	25
To change the length of the time lock	25
Weather timer	25
To set the Weather timer	25
To set the Weather timer frequency	25
Lawn Coverage	25
To disable the GPS Assisted Navigation	26
To enable the GPS Assisted Navigation	26
To set the Lawn coverage function	26
To do a test of the Lawn coverage function	27
To measure the distance from the charging station	27
To disable or enable the Lawn coverage function	27
To reset the Lawn coverage settings	27
Methods for the product to find the charging station	27
To set how the product finds the charging station	27
To do a test of the guide wire	28
To do a test of the boundary wire	28
To change the signal range of the charging station	28
To set the exit angles	28
To set the reversing distance	28
To set the Drive Past Wire function	29
Settings	29
Profiles	29
To save settings to a profile	29
To change the name of a profile	29
To use a profile	29
To connect a new charging station to a profile	29
ECO mode	29
Spiral Cutting	30
To set the level of Spiral Cutting	30
Slope control	30
To disable the Slope control	30
To set the time & date	30
To set the language	30
To set the country	30
To reset all user settings	30
The About menu	30
Accessories	31
Information	31
Automower® Connect app	31
To install the Automower® Connect app	31
Automower® Connect@Home (Automower® 310/315)	31
To pair Connect@Home and the product	31
To remove paired accounts	31
Automower® Connect	31
To pair Automower® Connect and the product	31
To enable the GeoFence function	32
To set a new center point for the Geofence function	32
To set the GeoFence level of sensitivity	32
To use the SMS function	32
Network	32
APN settings	32
Headlights	32
To set the schedule for the headlights	32
To set the Flashes when fault function	32
To avoid collisions with the mower house	33
Connectivity	33
Automower® Direct	33
To start to use Automower® Direct	33
Husqvarna Fleet Services™	33
To connect to the product with Husqvarna Fleet Services	33
Operation	34
Main switch	34
Start	34
Operating mode - Start	34
Main area	34
Secondary area	34
Override timer	35
Spot cutting (Automower® 315/315X)	35
Operating mode - Park	35
Park until further notice	35
Start again in 3 hours	35
Start on next timer	35
To stop the product	35
To switch off the product	35
Timer and Standby	35
Example 1	36
Example 2	36
To charge the battery	36
Adjust the cutting height	37
To adjust the cutting height	37
Maintenance	38
Introduction - maintenance	38
Clean the product	38
Chassis and blade disc	38
Chassis	38
Wheels	38
Cover	38
Charging station	38
Replace the blades	39
To replace the blades	39
Battery	39
Winter service	40
Troubleshooting	41
Introduction - troubleshooting	41
Fault messages	41
Information messages	46
Indicator lamp in the charging station	47
Symptoms	48
Find breaks in the loop wire	49
Transportation, storage and disposal	52
Transportation	52
Storage	52
Disposal	52
To remove the battery	52
Technical data	53
Technical data	53
Registered trademarks	55
Warranty	56
Warranty terms	56
Applicable to US/CA market	57
Supplier's Declaration of Conformity	57

Match case Limit results 1 per page

3.4 Installation of the product

3.4.1 To install the charging station

WARNING:

Obey national regulations

about electrical safety.

Read and understand the instructions about

the charging station. Refer to

To examine

where to put the charging station on page

Put the charging station in the selected area.

Connect the low-voltage cable to the

charging station.

Put the power supply at a minimum height of

30 cm / 12 in.

min 30 cm / 12”

CAUTION:

The product is only to

be used with the power supply

unit supplied by Husqvarna.

WARNING:

Do not put the power

supply at a height where there is a

risk it can be put in water. Do not

put the power supply on the

ground.

WARNING:

Do not encapsulate

the power supply. Condensed

water can harm the power supply

and increase the risk of electrical

shock.

Connect the power supply cable to a

100-240V outdoor power outlet.

WARNING:

Applicable to USA/

Canada. If power supply is

installed outdoors: Risk of Electric

Shock. Install only to a covered

Class A GFCI receptacle (RCD)

that has an enclosure that is

weatherproof with the attachment

plug cap inserted or removed.

Put the low-voltage cable in the ground with

stakes or bury the cable. Refer to

To put the

wire into position with stakes on page 22

To bury the boundary wire or the guide wire

on page 22

Connect the wires to the charging station.

Refer to

To install the boundary wire on

page 21

and

To install the guide wire on

page 22

Attach the charging station to the ground

with the supplied screws.

CAUTION:

Do not make new

holes in the charging station plate.

CAUTION:

Do not put your feet on

the charging station.

3.4.2 To install the boundary wire

Put the boundary wire around all of the work

area. Start and complete the installation

behind the charging station.

CAUTION:

Do not put unwanted

wire in a coil. The coil causes

interference with the product.

Open the connector and put the boundary

wire in the connector.

Close the connector with a pair of pliers.

Cut the boundary wire 1-2 cm / 0.4-0.8 in.

above each connector.

Put the right end of boundary wire into the

channel with the mark "AR".

Put the left end of boundary wire into the

channel with the mark "AL".

Push the right connector onto the metal pin

on the charging station with the mark "AR".

1220 - 001 - 08.07.2019

Installation -