Husqvarna RZ5424 Kohler Owners Manual - Page 37

Ignition System, Safety System

Get Husqvarna RZ5424 Kohler PDF manuals and user guides View all Husqvarna RZ5424 Kohler manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

MAINTENANCE Ignition System The engine is equipped with an electronic ignition system. Only the spark plugs require maintenance. For recommended spark plugs, see Technical Data. 1. Remove the ignition cable boot and clean around the spark plug. 2. Remove the spark plug with a spark plug socket wrench. 3. Check the spark plug. Replace the spark plug if fouled, the electrodes are burned and if the insulation is cracked or damaged. Clean the spark plug with a steel brush if it is to be reused. 4. Measure the electrode gap with a gapping tool. The gap should be .030" (0.75 mm). Adjust as necessary by bending the side electrode. 5. Reinsert the spark plug, turning by hand to avoid damaging the threads. 6. After the spark plug is seated, tighten it using a spark plug wrench so that the washer is compressed. A used spark plug should be turned 1/8 of a turn from the seated position. A new spark plug should be turned a ¼ turn from the seated position. 7. Replace the ignition cable. IMPORTANT INFORMATION Fitting the wrong spark plug type can damage the engine. Inadequately tightened spark plugs can cause overheating and damage the engine. Tightening the spark plugs too hard can damage the threads in the cylinder head. Measure the electrode gap 8011-054 Safety System The machine is equipped with a safety system that prevents starting or driving under the following conditions. The engine can only be started when: 1. The mower deck is disengaged. 2. The steering controls are in the outer, locked neutral position. 3. The parking brake is on. Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met. Change the conditions and try again. If the machine starts when one of these conditions is not met, turn the machine off and repair the safety system before using the machine again. Make sure the engine stops when the park brake is not engaged and the operator leaves the seated position. Check that the engine stops if the mower blades are engaged and the driver temporarily moves off the drivers seat. Steering controls locked in neutral 8058-026 IMPORTANT INFORMATION In order to be able to drive, the driver must sit in the seat and release the parking brake before the steering controls can be moved into the neutral position, otherwise the engine will stop. Husqvarna-37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
MAINTENANCE
Husqvarna-
37
Ignition System
The engine is equipped with an electronic ignition
system. Only the spark plugs require maintenance.
For recommended spark plugs, see Technical Data.
Remove the ignition cable boot and clean around
1.
the spark plug.
Remove the spark plug with a spark plug socket
2.
wrench.
Check the spark plug. Replace the spark plug
3.
if fouled, the electrodes are burned and if the
insulation is cracked or damaged. Clean the spark
plug with a steel brush if it is to be reused.
Measure the electrode gap with a gapping tool.
4.
The gap should be .030" (0.75 mm). Adjust as
necessary by bending the side electrode.
Reinsert the spark plug, turning by hand to avoid
5.
damaging the threads.
After the spark plug is seated, tighten it using
6.
a spark plug wrench so that the washer is
compressed. A used spark plug should be turned
1
/
8
of a turn from the seated position. A new spark
plug should be turned a ΒΌ turn from the seated
position.
Replace the ignition cable.
7.
IMPORTANT INFORMATION
Fitting the wrong spark plug type can damage
the engine.
Inadequately tightened spark plugs can
cause overheating and damage the engine.
Tightening the spark plugs too hard can
damage the threads in the cylinder head.
Safety System
The machine is equipped with a safety system that
prevents starting or driving under the following
conditions.
The engine can only be started when:
The mower deck is disengaged.
1.
The steering controls are in the outer, locked
2.
neutral position.
The parking brake is on.
3.
Make daily inspections to ensure that the safety
system works by attempting to start the engine
when one of the conditions is not met. Change the
conditions and try again.
If the machine starts when one of these conditions
is not met, turn the machine off and repair the safety
system before using the machine again.
Make sure the engine stops when the park brake is not
engaged and the operator leaves the seated position.
Check that the engine stops if the mower blades are
engaged and the driver temporarily moves off the
drivers seat.
IMPORTANT INFORMATION
In order to be able to drive, the driver must
sit in the seat and release the parking brake
before the steering controls can be moved into
the neutral position, otherwise the engine will
stop.
8011-054
Measure the electrode gap
8058-026
Steering controls locked in neutral