Husqvarna T535i XP Owner Manual - Page 15

General information about working technique, To prepare the product for operation in the tree

Get Husqvarna T535i XP PDF manuals and user guides View all Husqvarna T535i XP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

2. Push the battery release buttons and remove the battery from the battery holder to prevent accidental start. • To cut on the push stroke is when you cut with the top of the guide bar. The saw chain pushes the product in the direction of the operator. General information about working technique Below we give you some general information about how to use this product. WARNING: The information related to working technique in this operator's manual is not considered correct training to operate this tree-service product. This product must be used by tree-service operators with special training only! Use without the correct training can result in serious injuries. Do not try any task that you do not feel sure of! • To cut on the pull stroke is when you cut with the bottom of the guide bar. The saw chain pulls through the tree when you cut. In this position you have better control of the product and the position of the kickback zone. WARNING: Be careful when you cut on the push stroke. If the saw chain gets trapped in the trunk, the product can be pushed at you. You must prevent this force or there is a risk that the kickback zone of the guide bar touches the tree. This will lead to a kickback. • Use full power when you cut. • Let go of the power trigger after each cut. CAUTION: Motor damage can occur if you run the motor for too long at full power and without load. One example is if you cut without resistance from the saw chain. To prepare the product for operation in the tree Ground operator As a ground operator, do the steps that follow. 1. Examine the product. 2. Charge the battery. 3. Attach the end of an approved safety strop to the rope eyelet. 959 - 007 - 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
2.
Push the battery release buttons and remove the
battery from the battery holder to prevent accidental
start.
General information about working
technique
Below we give you some general information about how
to use this product.
WARNING:
The information related to
working technique in this operator's manual
is not considered correct training to operate
this tree-service product. This product must
be used by tree-service operators with
special training only! Use without the correct
training can result in serious injuries. Do not
try any task that you do not feel sure of!
•
To cut on the pull stroke is when you cut with the
bottom of the guide bar. The saw chain pulls through
the tree when you cut. In this position you have
better control of the product and the position of the
kickback zone.
•
To cut on the push stroke is when you cut with the
top of the guide bar. The saw chain pushes the
product in the direction of the operator.
WARNING:
Be careful when you cut on
the push stroke. If the saw chain gets
trapped in the trunk, the product can be
pushed at you. You must prevent this
force or there is a risk that the kickback
zone of the guide bar touches the tree.
This will lead to a kickback.
•
Use full power when you cut.
•
Let go of the power trigger after each cut.
CAUTION:
Motor damage can occur if
you run the motor for too long at full
power and without load. One example is
if you cut without resistance from the
saw chain.
To prepare the product for operation in
the tree
Ground operator
As a ground operator, do the steps that follow.
1.
Examine the product.
2.
Charge the battery.
3.
Attach the end of an approved safety strop to the
rope eyelet.
959 - 007 -
15