Husqvarna T540XP Mark III Owner Manual - Page 11

Assembly, Operation

Get Husqvarna T540XP Mark III PDF manuals and user guides View all Husqvarna T540XP Mark III manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Assembly Introduction WARNING: Read and understand the safety chapter before you assemble the product. 6. Align the hole in the guide bar with the chain adjuster pin and install the clutch cover. To assemble the guide bar and saw chain 1. Disengage the chain brake. 2. Loosen the bar nut and remove the clutch cover. Note: If the clutch cover is not easy to remove, tighten the bar nut, engage the chain brake and release. A click is heard if it is released correctly. 3. Assemble the guide bar onto the bar bolt. Move the guide bar to its most rear position. 4. Install the saw chain correctly around the drive sprocket and put it in the groove on the guide bar. WARNING: Always use protective gloves when you assemble the saw chain. 5. Make sure that the edges of the cutters point forward on the top edge of the guide bar. 7. Tighten the bar nut finger tight. 8. Tighten the saw chain. Refer to To adjust the tension of the saw chain on page 27 for instructions. 9. Tighten the bar nuts. Note: Some models have only one bar nut. To assemble the belt eyelet Use the belt eyelet to attach the product to a belt or harness. • To assemble the belt eyelet, speak to your servicing dealer. Operation Introduction WARNING: Read and understand the safety chapter before you use the product. To do a function check before you use the product 1. Make sure that the chain brake operates correctly and that it is not damaged. 2. Make sure that the throttle trigger lockout operates correctly and that it is not damaged. 3. Make sure that the start/stop switch operates correctly and that it is not damaged. 4. Make sure that there is no oil on the handles. 5. Make sure that the vibration damping system operates correctly and that it is not damaged. 6. Make sure that the muffler is correctly attached and that it is not damaged. 7. Make sure that all parts are correctly attached and not damaged or missing. 8. Make sure that the chain catcher is correctly attached. 1792 - 005 - 02.11.2022 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Assembly
Introduction
WARNING:
Read and understand the
safety chapter before you assemble the
product.
To assemble the guide bar and saw
chain
1.
Disengage the chain brake.
2.
Loosen the bar nut and remove the clutch cover.
Note:
If the clutch cover is not easy to remove,
tighten the bar nut, engage the chain brake and
release. A click is heard if it is released correctly.
3.
Assemble the guide bar onto the bar bolt. Move the
guide bar to its most rear position.
4.
Install the saw chain correctly around the drive
sprocket and put it in the groove on the guide bar.
WARNING:
Always use protective
gloves when you assemble the saw
chain.
5.
Make sure that the edges of the cutters point forward
on the top edge of the guide bar.
6.
Align the hole in the guide bar with the chain adjuster
pin and install the clutch cover.
7.
Tighten the bar nut finger tight.
8.
Tighten the saw chain. Refer to
To adjust the tension
of the saw chain on page 27
for instructions.
9.
Tighten the bar nuts.
Note:
Some models have only one bar nut.
To assemble the belt eyelet
Use the belt eyelet to attach the product to a belt or
harness.
•
To assemble the belt eyelet, speak to your servicing
dealer.
Operation
Introduction
WARNING:
Read and understand the
safety chapter before you use the product.
To do a function check before you use
the product
1.
Make sure that the chain brake operates correctly
and that it is not damaged.
2.
Make sure that the throttle trigger lockout operates
correctly and that it is not damaged.
3.
Make sure that the start/stop switch operates
correctly and that it is not damaged.
4.
Make sure that there is no oil on the handles.
5.
Make sure that the vibration damping system
operates correctly and that it is not damaged.
6.
Make sure that the muffler is correctly attached and
that it is not damaged.
7.
Make sure that all parts are correctly attached and
not damaged or missing.
8.
Make sure that the chain catcher is correctly
attached.
1792 - 005 - 02.11.2022
11