IBM 43635gu User Guide - Page 48

drive assembly into the drive bay until it stops and release the loops.

Get IBM 43635gu - Servers System X3200 Xeon 2.13ghz PDF manuals and user guides
UPC - 883436002950
View all IBM 43635gu manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

To install a simple-swap hard disk drive, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 18. 2. Turn off the server and peripheral devices and disconnect all external cables and power cords. 3. Unlock the side cover (the bezel will not disengage from the server if the cover is locked). 4. Remove the side cover and lower bezel (see "Removing the side cover" on page 21 and "Removing the two-piece bezel" on page 22). 5. Touch the static-protective package that contains the drive to any unpainted metal surface on the server; then, remove the drive from the package and place it on a static-protective surface. 6. Align the drive assembly with the guide rails in the bay (the connector end of the drive goes in first). 7. Pull the loops of the drive assembly toward each other; then, carefully slide the drive assembly into the drive bay until it stops and release the loops. Note: Do not release the loops on the drive assembly until it is completely seated. If you have other devices to install or remove, do so now; otherwise, go to "Completing the installation" on page 47. The simple-swap-drive backplate controls the IDs for the internal simple-swap drive bays. The following table lists the IDs for the hard disk drives and backplate that are connected to simple-swap models. Table 2. Device ID Drive bay 4 0 Drive bay 5 1 Drive bay 6 2 Drive bay 7 3 34 System x3200 Types 4362 and 4363: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
To install a simple-swap hard disk drive, complete the following steps:
1.
Read the safety information that begins on page v and “Installation guidelines”
on page 18.
2.
Turn off the server and peripheral devices and disconnect all external cables
and power cords.
3.
Unlock the side cover (the bezel will not disengage from the server if the cover
is locked).
4.
Remove the side cover and lower bezel (see “Removing the side cover” on
page 21 and “Removing the two-piece bezel” on page 22).
5.
Touch the static-protective package that contains the drive to any unpainted
metal surface on the server; then, remove the drive from the package and place
it on a static-protective surface.
6.
Align the drive assembly with the guide rails in the bay (the connector end of
the drive goes in first).
7.
Pull the loops of the drive assembly toward each other; then, carefully slide the
drive assembly into the drive bay until it stops and release the loops.
Note:
Do not release the loops on the drive assembly until it is completely
seated.
If you have other devices to install or remove, do so now; otherwise, go to
“Completing the installation” on page 47.
The simple-swap-drive backplate controls the IDs for the internal simple-swap drive
bays. The following table lists the IDs for the hard disk drives and backplate that
are connected to simple-swap models.
Table 2.
Device
ID
Drive bay 4
0
Drive bay 5
1
Drive bay 6
2
Drive bay 7
3
34
System x3200 Types 4362 and 4363: User’s Guide