IBM IC25N040ATCS04 Hard Drive Specifications - Page 45

Connector and jumper description, 5.4 Mounting orientation - 0 jumper

Get IBM IC25N040ATCS04 - Travelstar 40 GB Hard Drive PDF manuals and user guides View all IBM IC25N040ATCS04 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Figure 27. Mounting hole locations of all models except 60 GB model. 6.5.3 Connector and jumper description A jumper is used to designate the drive address as either master or slave. The jumper setting method is described in section 7.10, "Drive address setting" on page 58. Connector specifications are included in section 7.2, "Interface connector" on page 41. 6.5.4 Mounting orientation The drive will operate in all axes (six directions) and will stay within the specified error rates when tilted ±5 degrees from these positions. Performance and error rate will stay within specification limits if the drive is operated in the other permissible orientations from which it was formatted. Thus a drive formatted in a horizontal orientation will be able to run vertically and vice versa. The recommended mounting screw torque is 3.0±0.5 kgf-cm. The recommended mounting screw depth is 3.0±0.3 mm for bottom and 3.5±0.5 mm for horizontal mounting. Travelstar 60GH & 40GN hard disk drive specifications 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
Figure 27. Mounting hole locations of all models except 60 GB model.
6.5.3 Connector and jumper description
A jumper is used to designate the drive address as either master or slave. The jumper setting method is
described in section 7.10, "Drive address setting" on page 58.
Connector specifications are included in section 7.2, "Interface connector" on page 41.
6.5.4 Mounting orientation
The drive will operate in all axes (six directions) and will stay within the specified error rates when tilted
±5 degrees from these positions.
Performance and error rate will stay within specification limits if the drive is operated in the other permis-
sible orientations from which it was formatted. Thus a drive formatted in a horizontal orientation will be
able to run vertically and vice versa.
The recommended mounting screw torque is 3.0±0.5 kgf-cm.
The recommended mounting screw depth is 3.0±0.3 mm for bottom and 3.5±0.5 mm for horizontal
mounting.
Travelstar 60GH & 40GN hard disk drive specifications
32