Icom IC-F9011 / F9021 Instruction Manual - Page 27

SPEAKER MICROPHONE, ■ Optional HM-184 description, ■ To attach

Get Icom IC-F9011 / F9021 PDF manuals and user guides View all Icom IC-F9011 / F9021 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

6 SPEAKER MICROPHONE ■ Optional HM-184 description ■ To attach 1 Microphone Speaker Attach the connector of the speaker-microphone into the 2 multi connector on the transceiver and tighten the screw with 3 a coin or flat head screwdriver. 4 PTT SWITCH Push and hold to transmit; release to receive. Turn the transceiver power OFF while connecting the HM-184. Belt clip NEVER immerse the connector in water. If the connector becomes wet, be sure to dry it BEFORE attaching it to the transceiver. 5 Screw 6 7 Coin 8 CAUTION: Attach the 9 multi connector properly, but do not overtighten. 10 A loose connection will al- 11 low water intrusion into the connector; an overtight- 12 ened connection will dam- age the connector pins in 13 the transceiver. 14 NOTE: The microphone is located as shown in the diagram above. To maximize the readability of your transmitted signal (voice), hold the microphone approx. 5 to 10 cm (2 to 4 inches) from your mouth, and speak in a normal voice level. 15 IMPORTANT: KEEP the connector cover attached to the transceiver when the speaker-microphone is not in use. 16 (p. 3) Water will not get into the transceiver even if the cover is not attached; however, the terminals (pins) will become rusty, or the transceiver will function abnormally if the con- nector gets wet. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
22
6
SPEAKER MICROPHONE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
■
Optional HM-184 description
Turn the transceiver
power OFF while con-
necting the HM-184.
Speaker
Belt clip
Microphone
PTT SWITCH
Push and hold to
transmit;
release to receive.
NEVER
immerse the connector in water. If the connector
becomes wet, be sure to dry it BEFORE attaching it to the
transceiver.
NOTE:
The microphone is located as shown in the diagram
above. To maximize the readability of your transmitted sig-
nal (voice), hold the microphone approx. 5 to 10 cm (2 to 4
inches) from your mouth, and speak in a normal voice
level.
■
To attach
Attach the connector of the speaker-microphone into the
multi connector on the transceiver and tighten the screw with
a coin or flat head screwdriver.
CAUTION:
Attach
the
multi connector properly,
but do not overtighten.
A loose connection will al-
low water intrusion into the
connector; an overtight-
ened connection will dam-
age the connector pins in
the transceiver.
Coin
Screw
IMPORTANT:
KEEP
the connector cover attached to the
transceiver when the speaker-microphone is not in use.
(p. 3)
Water will not get into the transceiver even if the cover is
not attached; however, the terminals (pins) will become
rusty, or the transceiver will function abnormally if the con-
nector gets wet.