Icom IC-FR5200H Ic-fr5200h/fr6200h Instructions - Page 1
Icom IC-FR5200H Manual
View all Icom IC-FR5200H manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
DDRear panel connection CONNECTION ACC CONNECTOR Used for external equipment control. To an RX antenna*1 To a [LAN] port of the IC-FC5000E (dPMR) or a To a TX PC console through a antenna*1 Hub or a router (NXDN)*2. AC outlet DC power supply*1 NXDN: 13.6 V dPMR: 13.2 V (at least 20 A) Red Black +_ ACC SPEAKER RX IF TX LAN BUS-2 BUS-1 FUSE GND ¬ + DC INPUT¬ - DC power cable FUSE EXTERNAL SPEAKER*1 Connect a 4 ø external speaker. SP-35/SP-35L PC console connection (only for NXDN) To an Ethernet port Hub*1 // only for the NXDN version // The illustration to the right describes one example of a connection for trunking mode operation. Up to 30 repeaters can be daisy-chained. Repeater LAN BUS-2 BUS-1 CAT-5 straight cable*1 LAN BUS-2 BUS-1 LAN BUS-2 BUS-1 PC console*1 To the [LAN] connector of the repeater *1 Purchase separately. *2 See the illustration to the left for the PC console connection through a Hub (NXDN). • Grounding To prevent electrical shock, television interference (TVI), broadcast interference (BCI) and other problems, ground the repeater using the GROUND [GND] terminal on the rear panel. For best results, connect a heavy gauge wire or strap to a long ground rod. Make the distance between the [GND] terminal and ground rod as short as possible. R WARNING! NEVER connect the [GND] terminal to a gas or electric pipe, since the connection could cause an explosion or electric shock. • Power supply Make sure the repeater's power is OFF when connecting a DC power cable. CAUTION: Voltages greater than 16 V DC will damage the repeater. Check the source voltage before connecting the power cable. • Antenna For repeater communications, an antenna is a critical component, along with output power and sensitivity. Select antenna(s), such as a well-matched 50 ø antenna, and feedline. A 1.5:1 or better Voltage Standing Wave Ratio (VSWR) is recommended for a desired band. Of course, the transmission line should be a coaxial cable. If you want to connect only one antenna for both transmission and reception, use a third-party duplexer. CAUTION: Protect the repeater from lightning by using a lightning arrestor. NOTE: There are many publications that describe proper antennas and their installation. Check with your local dealer for more information and recommendations. - 4 - INSTRUCTIONS VHF REPEATER Iç-FR5200H UHF REPEATER Iç-FR6200H Thank you for choosing this Icom product. READ ALL INSTRUCTIONS carefully and completely before using this product. FOREWORD This instruction sheet includes some functions that are usable only when they are preset by your dealer. Ask your dealer for details. SUPPLIED ACCESSORIES Handles For the handles installation Spacers Allen wrench Screws DC power cable Spare fuse (FGB01 30 A) OPTIONS • SP-35/SP-35L external speakers Input impedance : 4 ø Maximum input power : 7 W • HM-152 hand microphone • SM-26 desktop microphone Some options may not be available in some countries. Please ask your dealer for details. FUSE REPLACEMENT If a fuse blows or the repeater stops functioning, try to find the source of the problem, and then replace the damaged fuse with a new rated one. ❑ Fuse rating: 30 A USE only a 30 A fuse. Rack Function name stickers*1 KEY SEAL *1 Used for labelling the programmable function keys according to their assinged functions. Icom is not responsible for the destruction, damage to, or performance of any Icom or non-Icom equipment, if the malfunction is because of: • Force majeure, including, but not limited to, fires, earth- DISPOSAL quakes, storms, floods, lightning, other natural disasters, disturbances, riots, war, or radioactive contamination. • The use of Icom transceivers with any equipment that is The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you not manufactured or approved by Icom. that in the European Union, all electrical and electronic products, batteries, and accumula- Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, and/or other countries. dPMR and the dPMR logo are trademarks of the dPMR MoU Association NXDN is a trademark of Icom Incorporated and JVC Kenwood Corporation. All other products or brands are registered trademarks or trademarks of their respective holders. tors (rechargeable batteries) must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to the laws in your area. - 1 - 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-7189D-2EX-q Printed in Japan © 2014-2017 Icom Inc.