Icom IC-FR5200H Ic-fr5200h/fr6200h Instructions - Page 2

DDFront panel PANEL DESCRIPTION e r Function Speaker q display w t P0 P1 P2 P3 P4 q VOLUME CONTROL [VOLUME] Rotate to adjust the audio output level. w SELECTOR DIAL [SELECT] Rotate to adjust the squelch threshold level, or select an operating channel (depending on the presetting). e POWER INDICATOR [PWR] Lights green at 'A' module's indicator while the repeater power is ON. r TRANSMIT INDICATOR [TX] Lights red at 'A' module's indicator while transmitting. t BUSY INDICATOR [BUSY] Lights green at 'A' module's indicator while receiving a signal or when the squelch is open. i uy y MICROPHONE CONNECTOR [MIC] Connect an optional microphone. CAUTION: DO NOT detach the [MIC] connector cover when optional microphone is not in use to prevent dust from entering. u POWER SWITCH [POWER] ➥ Push to turn ON the power. ➥ Hold down for 3 seconds to turn OFF the power. i DEALER-PROGRAMMABLE KEYS Desired functions can be independently preset by your dealer. Ask your dealer for details. DDFunction display q w e rt y ICOM Inc. q SIGNAL STRENGTH INDICATOR Displays the relative receive signal strength level. w LOW POWER INDICATOR Displayed when the low output power is selected. e AUDIBLE INDICATOR Displayed when a channel is in the 'audible' (unmute) mode. r COMPANDER INDICATOR Displayed when the compander function is activated. t SCRAMBLER/ENCRYPTION INDICATOR Displayed when the Voice Scrambler or the Encryption function is activated. y CHARACTER READOUT Displays a variety of texts or codes. - 2 - DDRear panel PANEL DESCRIPTION (Continued) ACC LAN BUS-2 BUS-1 SPEAKER RX IF TX FUSE GND ¬ + DC INPUT¬ - FUSE qw e r t y* ui o * only for the NXDN version q D -SUB 25-PIN [ACC] Connects an external unit. Ask your dealer for details. w EXTERNAL SPEAKER CONNECTOR [SPEAKER] Connects the optional SP-35 or SP-35L. e RECEIVE ANTENNA CONNECTOR [RX] Connects a receive antenna (impedance: 50 ø) and in- puts received signals. r TRANSMIT ANTENNA CONNECTOR [TX] Connects a transmit antenna (impedance: 50 ø) and out- puts transmitting signals. t LAN CONNECTOR [LAN] For an Ethernet connection, connect the repeater to an Ethernet [LAN] port of a PC console, through a Hub or a router (NXDN), or to the [LAN] port of the IC-FC5000E (dPMR). // only for the NXDN version // In the trunking mode operation, the repeater at one end of the chain must be connected. You can control the repeater and all others in the chain from the PC console. // only for the dPMR version // In the trunking mode operation, connect to the [LAN] port of the IC-FC5000E. y BUS CONNECTORS [BUS-1]/[BUS-2] // only for the NXDN version // For data communication between controllers in the trunking mode operation, you can use either [BUS-1] or [BUS-2]. Through the connectors, the controllers can be "daisy-chained" together, and form a network that can pass the trunking and other data among the controllers. u FUSE HOLDER  See page 1 to replace a damaged fuse. i GROUND TERMINAL [GND] Connect this terminal to ground to prevent electrical shocks, TVI, BCI, and other problems. See page 4 for the grounding details. o DC POWER CONNECTOR [DC INPUT]  Connects a supplied DC power cable from this connector to an external 13.6 V (NXDN) or 13.2 V (dPMR) DC power supply (purchase separately). See page 4 for the connection details. INSTALLATION DDInstalling handles to the repeater The supplied handles are used to mount the repeater into the supplied rack. The handles can be installed to the repeater's front panel. qqA ttach the supplied handles to both sides of the repeater's front panel with the spacers, then tighten the screws as described below. wwT he completed installation should look like as described below. P0 P1 P2 P3 P4 Handle Spacer Screw - 3 - P0 P1 P2 P3 P4