Icom IC-M72 Instruction Manual - Page 36

Troubleshooting

Get Icom IC-M72 PDF manuals and user guides View all Icom IC-M72 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

11 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION REF. The transceiver does not • The battery is depleted. turn ON. • Bad connection to the battery pack. • Recharge the battery pack. • Check the connection to the transceiver. pgs. 25-27 p. 3 No sound from the • Squelch level is too tight. speaker. • Volume level is too low. • Speaker has been exposed to water. • Water has entered to [SP MIC] connector. • Set squelch to the threshold point. • Rotate [VOL] to set a suitable level. • Push and hold both [16•9] and [H/L•LOCK] to drain water from the speaker. • Dry [SP MIC] connector. p. 11 p. 9 p. 12 - Transmitting is impossible, • Some channels are for low power or receive • Change channels. or high power can not be only. selected. • The battery is exhausted. • Recharge the battery pack. • The battery is overcharged. • The output power is set to low. • Verify the battery voltage is correct. • Push [H/L•LOCK] to select high power. pgs. 8, 9, 31 pgs. 25-27 - p. 9 The displayed channel • Lock function is activated. cannot be changed. • Push [H/L•LOCK] for 1 sec. to cancel the function. p. 10 Scan does not start. • "TAG" channels are not programmed. • Set the desired channels as "TAG" channels. p. 15 No beeps. • Beep tones are turned OFF. • Set the beep tones to ON (Fix Beep/User Beep) in p. 18 the SET mode. Self check error. (Temperature) • The temperature is outside of -35°C to +73°C; • Leave the transceiver at room temperature for a - -31°F to +163°F (approx.). while. Turn the power ON to check if the internal temperature has returned to normal. Self check error. • The connected battery pack's voltage is more • Verify the battery voltage is correct. - (Battery voltage) than 11 V. Transmitting continuously • Ambient noise is too loud. while not speaking when using VOX function. • Push [ ] and [H/L•LOCK] to deactivate the VOX function. • Set the VOX gain to lower sensitive value. p. 12 p. 22 "CHARGE" comment • The connected battery is depleted. blinks 30 • Recharge the battery pack. pgs. 25-27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
PROBLEM
The transceiver does not
turn ON.
No
sound
from
the
speaker.
Transmitting is impossible,
or high power can not be
selected.
The displayed channel
cannot be changed.
Scan does not start.
No beeps.
Self check error.
(Temperature)
Self check error.
(Battery voltage)
Transmitting continuously
while not speaking when
using VOX function.
“
CHARGE
”
comment
blinks
30
TROUBLESHOOTING
11
POSSIBLE CAUSE
•
The battery is depleted.
•
Bad connection to the battery pack.
•
Squelch level is too tight.
•
Volume level is too low.
•
Speaker has been exposed to water.
•
Water has entered to
[SP MIC]
connector.
•
Some channels are for low power or receive
only.
•
The battery is exhausted.
•
The battery is overcharged.
•
The output power is set to low.
•
Lock function is activated.
•“
TAG
”
channels are not programmed.
•
Beep tones are turned OFF.
•
The temperature is outside of
–
35
°
C to +73
°
C;
–
31
°
F to +163
°
F (approx.).
•
The connected battery pack
’
s voltage is more
than 11 V.
•
Ambient noise is too loud.
•
The connected battery is depleted.
SOLUTION
•
Recharge the battery pack.
•
Check the connection to the transceiver.
•
Set squelch to the threshold point.
•
Rotate
[VOL]
to set a suitable level.
•
Push and hold both
[16
•
9]
and
[H/L
•
LOCK]
to
drain water from the speaker.
•
Dry
[SP MIC]
connector.
•
Change channels.
•
Recharge the battery pack.
•
Verify the battery voltage is correct.
•
Push
[H/L
•
LOCK]
to select high power.
•
Push
[H/L
•
LOCK]
for 1 sec. to cancel the function.
•
Set the desired channels as
“
TAG
”
channels.
•
Set the beep tones to ON (Fix Beep/User Beep) in
the SET mode.
•
Leave the transceiver at room temperature for a
while. Turn the power ON to check if the internal
temperature has returned to normal.
•
Verify the battery voltage is correct.
•
Push
[
]
and
[H/L
•
LOCK]
to deactivate the
VOX function.
•
Set the VOX gain to lower sensitive value.
•
Recharge the battery pack.
REF.
pgs.
25
–
27
p. 3
p. 11
p. 9
p. 12
—
pgs. 8, 9,
31
pgs.
25
–
27
—
p. 9
p. 10
p. 15
p. 18
—
—
p. 12
p. 22
pgs.
25
–
27