Icom M400BB Instruction Manual - Page 11

ATIS code programming

Get Icom M400BB PDF manuals and user guides View all Icom M400BB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

PREPARATION 2 ■■ATIS code programming (For Dutch version transceivers) 1 The 10 digit ATIS (Automatic Transmitter Identification System) code can be programmed at power ON. 2 rrRepeat step e to enter all 10 digits. ttAfter entering the 10 digit code, "FINISH" is automatically 3 The code is programmed by using the HM-195. selected, and then push [ENT] or Dial to set it. yyThe "ATIS CONFIRMATION" screen is displayed. 4 This initial code setting can be performed only once. 5 After being set, it can be changed by only your dealer or distributor. If your ATIS code has already been pro- 6 grammed, this programming is not necessary. 7 qqAfter programming the MMSI code, "Push [ENT] to Register Your ATIS" is displayed. wwPush [ENT] to start the ATIS code programming. • Push [CLEAR] twice to cancel the programming, and go to the normal operating mode. In this case, the ATIS function is disabled. To program the ATIS code, turn OFF the power, then turn it ON again. eeEnter your ATIS code in the following manner: • Select a desired number using Dial, or Push [ENT] or Dial to set it. • T o move the cursor, select either arrow, "←" or "→," then push [ENT] or Dial. 8 uuEnter your ATIS code again for confirmation. 9 • Enter in the same manner as steps e through t. 10 iiWhen your ATIS code programming is successfully com- pleted, the screen shown below is briefly displayed. 11 • After that, the normal operating screen is displayed. 12 13 14 15 16 The programmed ATIS code can be checked in the MENU screen. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
3
2
PREPARATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
The 10 digit ATIS (Automatic Transmitter Identification Sys-
tem) code can be programmed at power ON.
The code is programmed by using the HM-195.
This initial code setting can be performed only once.
After being set, it can be changed by only your dealer
or distributor. If your ATIS code has already been pro-
grammed, this programming is not necessary.
After programming the MMSI code, “Push [ENT] to Regis-
q
ter Your ATIS” is displayed.
Push [ENT] to start the ATIS code programming.
w
• Push [CLEAR] twice to cancel the programming, and go to the
normal operating mode. In this case, the ATIS function is dis-
abled. To program the ATIS code, turn OFF the power, then turn
it ON again.
Enter your ATIS code in the following manner:
e
• Select a desired number using Dial, or [
∫
]/[
√
]/[
Ω
]/[
≈
].
• Push [ENT] or Dial to set it.
•To move the cursor, select either arrow, “
←
” or “
→
,” then push
[ENT] or Dial.
Repeat step
r
e
to enter all 10 digits.
After entering the 10 digit code, “FINISH” is automatically
t
selected, and then push [ENT] or Dial to set it.
The “ATIS CONFIRMATION” screen is displayed.
y
Enter your ATIS code again for confirmation.
u
• Enter in the same manner as steps
e
through
t
.
When your ATIS code programming is successfully com-
i
pleted, the screen shown below is briefly displayed.
• After that, the normal operating screen is displayed.
The programmed ATIS code can be checked in the MENU
screen.
ATIS code programming
■
(For Dutch version transceivers)