Icom M400BB Instruction Manual - Page 23

Trouble Shooting

Get Icom M400BB PDF manuals and user guides View all Icom M400BB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

7 TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION REF. 1 The transceiver does • Bad connection to the power supply. • Check the connection to the transceiver and p. 6 2 not turn ON. Little or no sound comes • Squelch level is set too high. power supply. • Set the squelch to the threshold point. ⁄1* 3 from the speaker. • Volume level is set too low. • Set the volume to a suitable level. ⁄0* 4 • Speaker has been exposed to water. • Remove the water with the AquaQuake func- .* tion. 5 Transmitting is impossi- • S ome channels are programmed for low • Change channels. b*, 6 ble, or high power can- power or receive only by regulations. not be selected. • The output power is set to low. • Push [HI/LO] to select high power. pp. 13, 14 n* 7 Scan does not start. • Favorite channels are not programmed. • S et the desired channels as Favorite chan- ⁄3* 8 nels. 9 No beep sounds. • Beep tones are turned OFF. • T urn the beep tones ON in the CONFIGURA- ‹0* TION menu. 10 Distress calls cannot be • M MSI (DSC self ID) code is not pro- • P rogram the MMSI (DSC self ID) code. p. 2 11 transmitted. grammed. 12 * Refer to the HM-195 commandmiciv™ instruction manual. 13 14 15 16 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
15
7
TROUBLE SHOOTING
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PROBLEM
POSSIBLE CAUSE
SOLUTION
REF.
The transceiver does
not turn ON.
• Bad connection to the power supply.
• Check the connection to the transceiver and
power supply.
p. 6
Little or no sound comes
from the speaker.
• Squelch level is set too high.
• Volume level is set too low.
• Speaker has been exposed to water.
• Set the squelch to the threshold point.
• Set the volume to a suitable level.
• Remove the water with the AquaQuake func
-
tion.
⁄
1
*
⁄
0
*
.
*
Transmitting is impossi-
ble, or high power can-
not be selected
.
• Some channels are programmed for low
power or receive only by regulations.
• The output power is set to low.
• Change channels.
• Push [HI/LO] to select high power.
b
*
,
pp. 13, 14
n
*
Scan does not start.
• Favorite channels are not programmed.
• Set the desired channels as Favorite chan
-
nels.
⁄
3
*
No beep sounds.
•Beep tones are turned OFF.
•Turn the beep tones ON in the CONFIGURA
-
TION menu.
‹
0
*
Distress calls cannot be
transmitted.
• MMSI
(DSC
self
ID)
code
is
not
pro
-
grammed.
• Program the MMSI (DSC self ID) code.
p. 2
* Refer to the HM-195
COMMANDMIC
IV
™
instruction manual.