Icom VE-PG4 Instruction Manual
Icom VE-PG4 Manual
View all Icom VE-PG4 manuals
Add to My Manuals
Save this manual to your list of manuals |
Icom VE-PG4 manual content summary:
- Icom VE-PG4 | Instruction Manual - Page 1
and other necessary settings. (See the repeater and VE-PG3 or VE-PG4 instruction manuals for settings details.) 2 Turn OFF the both the repeater and the VE-PG3 or VE-PG4, and then connect the OPC-2390, as shown below. VE-PG4 (Rear view) Icom's repeater (IC-FR5000/IC-FR6000 series) A1~A4 B1~B4 C1 - Icom VE-PG4 | Instruction Manual - Page 2
*3 2 near the connector. *2 Remove the cable from the VE-PG3 1234 or VE-PG4, before cutting the wires. *3 DO NOT cut the wires too short. Oth- erwise to the laws in your area. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United
CONNECTION CABLE
INSTRUCTIONS
Thank you for choosing this Icom product.
The OPC-2390
CONNECTION
CABLE
is used to connect a
serial communication device to the VE-PG3 or VE-PG4.
READ ALL INSTRUCTIONS
carefully and completely
before using this product.
OPC-2390
Turn OFF the both the repeater and the VE-PG3 or VE-PG4, and then connect the OPC-2390, as shown below.
2
Set the repeater channel, TX output power, and other necessary settings.
(See the repeater and VE-PG3 or VE-PG4 instruction manuals for settings details.)
1
CONNECTING THE OPC-2390
CAUTION
• Verify that both the repeater and the VE-PG3 or VE-PG4 are turned OFF when connecting or disconnecting the cable.
• Hold the connector body when connecting or disconnecting them.
• Never bend or pinch the cable.
• Never place a heavy object on the cable.
• Never touch the cable with wet hands.
• Always connect the cable correctly. An incorrect connection could damage the VE-PG3 or VE-PG4 and/or the repeater.
When other cables are connected, you can
use
needle-nose pliers to carefully insert or
remove connectors.
VE-PG4 (Rear view)
VE-PG4 (Rear view)
Needle-nose pliers
Needle-nose pliers
NEVER pull the connector by holding the
cable. This will damage the cable.
*If the cable becomes damaged, replace
the connector(s). See “REPLACING THE
CONNECTOR” on the reverse side for
replacement details.
Connector
body
Connector
body
VE-PG4 (Rear view)
OPC-2390
• This is an example of connecting a repeater to the [EXT1] port.
A1
~
A4
A1
~
A4
B1
~
B4
B1
~
B4
C1
~
C4
C1
~
C4
A1
~
A4
A1
~
A4
B1
~
B4
B1
~
B4
C1
~
C4
C1
~
C4
A1
~
A4
A1
~
A4
B1
~
B4
B1
~
B4
C1
~
C4
C1
~
C4
A
BC
Be sure to insert the
connectors top side up.
Bottom
Top
A
1
2
3
4
Icom’s repeater
(IC-FR5000/IC-FR6000 series)
To the accessory connector
B
A
C