Image Fitness 518 English Manual
Image Fitness 518 Manual
 |
View all Image Fitness 518 manuals
Add to My Manuals
Save this manual to your list of manuals |
Image Fitness 518 manual content summary:
- Image Fitness 518 | English Manual - Page 1
'ft".... ......s..o. * ..../. .. ..i.r...iI,...I.I 7.....".. i -. e Ms... e°.,.4 • : I; "III 1`% 44 IIIIIIIMW OWNER'S MANUAL CAUTION!: Read all safety precautions and instructions In this manual before using this equipment. Keep this manual in a safe place for future reference. - Image Fitness 518 | English Manual - Page 2
before using the IMAGE 518. 1. Read all instructions in this owner's manual and in the accompanying literature before using the IMAGE 518. Use the IMAGE 518 only as described. 2. Inspect and tighten all parts each time you use the IMAGE 518. Replace any worn parts immediately. 3. Keep your - Image Fitness 518 | English Manual - Page 3
to achieve the specific results you want. For your safety and benefit, read this manual and the accompanying literature before using the IMAGE 518. If you have additional questions, please call our Customer Service Department toll-free at 1400-753-4645, Monday through Friday, 9 a.m. until 6 p.m. EST - Image Fitness 518 | English Manual - Page 4
drawings. Refer to the PART IDENTIFICATION (ID) CHART accompanying this owner's manual for help identifying the small parts used in assembly. Due to the size and weight of the image 518, it should be assembled in the location where it will be used. Place all parts of the IMAGE 518 in a cleared area - Image Fitness 518 | English Manual - Page 5
4. Attach three Pulleys (9) to the "U" Stabilizer (83) with 3/8" x 2" Shank Bolts (8) and 3/8" Nylock Nuts (1). Press three 2" x 2" Outer Caps (10) onto the "U" Stabilizer (83). Attach the "U" Stabilizer (83) to the Base (89) with two 3/8" x 3" Bolts (7), four 3/8" Washers (2) and two 3/8" Nylock - Image Fitness 518 | English Manual - Page 6
7. Attach a Pulley (9) to the Frame Top (80) with a 3/8" x 2" -Shank'Bolt"(8) and 3/Er NylocicNut 7 (1). Press a 2" x 2" Inner Cap (11) into the Frame Top (80). 8. Attach the center of the Frame Top-(80) to the Front Upright (72) with two 3/8" x 3" Bolts (7), 8 four 3/8" Washers (2) and two - Image Fitness 518 | English Manual - Page 7
. -: TT i_i01 9 9 8 . 12. Apply grease to the threaded post on the Right Butterfly Arm (75). Insert the post up through the Butterfly Arm Support (73). Tighten a 1/2" Nylock Nut (22) with an 11/16" Washer (21) onto the post. Do not overtighten the Nylock Nut. Press a 1 1/2" x 1 1/2" Inner Cap - Image Fitness 518 | English Manual - Page 8
14. Attach the Leg Lever Frame (70) to the 14 Butterfly Upright (77) with two 3/8" x 3" Bolts (7), four 3/8" Washers (2) and two 3/8" Nylock Nuts (1). Press a 2" x 2" Inner Cap (11) into the Leg Lever Frame (70). 15. Attach a Pulley (9) to the lower end of the Leg 15 Lever (71) with a 3/8" x - Image Fitness 518 | English Manual - Page 9
17. Press a 1" x 2" Inner Cap (5) into each end of 17 the Short Seat Post (69). Slide a Handle Grip (14) onto each end of a "U" Handle (68). It may be helpful to wet the "U" Handle with soapy water. Attach the "U" Handle (68) and the Short Seat Post (69) to the Large Seat (63) with two 3/8" x 1 - Image Fitness 518 | English Manual - Page 10
20. Find the ends of two Handles (13) that contain inset nuts. Insert those ends of the 20 Handles into the VKR Frame (67). Attach each Handle with an 8mm x 3/4" Bolt (6) and an 8mm Washer (4). Press a 2" x 2" Outer Cap w/Hole (28) onto each end of the VKR Frame (67). Slide a Handle Grip (14) - Image Fitness 518 | English Manual - Page 11
24. Press two 2" x 2" Inner Caps (11) into the 24 posts on the Press Arm (102). Tighten the Pin Knob (44) onto the 103/4" Pin (43). Hold the Adjuster (103) between the posts on the Press Arm (102) as shown. To make sure that the Adjuster is turned correctly, note the position of the long end of - Image Fitness 518 | English Manual - Page 12
27 Top (80) as shown with the two 3/16" Screws (40). 40 28. Insert a 3/8" x 2 3/4" Shank Bolt (29) into one 28 side of the Leg Press Support (99). Slide a 3/4" x 5/16" Spacer (19), a Pulley (9) and another 3/4" x 5/16" Spacer onto the Bolt. Insert the Bolt through the other side of the Leg - Image Fitness 518 | English Manual - Page 13
29. Hold the Leg Press "H" Frame (98) in a vertical position and press two 2" x 2" Inner Caps (11) into the upper end. Insert four 5/8" Bushings (24) into the lower end of the Leg Press "H" Frame (98), and two 5/8" Bushings into the Leg Press Stabilizer (96). Grease the insides of all six Bushings. - Image Fitness 518 | English Manual - Page 14
end of the Leg Press Rail (100). Insert the Sleeve and the Leg Press Rail into the top of the Leg Press Support (99). Connect the Leg Press Support, Sleeve and Leg Press Rail with a 3/8" x 3" Bolt (7), two 3/8" Washers (2) and a 3/8" Nylock Nut (1). 35 ''2 7 72 2 _4( tel 1 1O0 2 Attach the Leg - Image Fitness 518 | English Manual - Page 15
36. Press a Tube Cap (39) into each end of a Pad Tube (58). Insert the Pad Tube (58) into the Leg Press Frame (101). Center the Pad Tube and slide a 6" Foam Pad (59) onto each end of it. Attach the Leg Press Backrest (61) to the Leg Press Frame (101) with two 3/8" x 2 3/4" Bolts (16) and 3/8" - Image Fitness 518 | English Manual - Page 16
89 88 "." 40. Slide 19 Weights (84) down onto each pair of Weight Guides (56). Make sure the Weights 40 are turned so the pin grooves are downward and 86) and a Weight 41 Selector (57) down onto each pair of Weight Guides (56). Make sure the holes in the sides of the Top Weights are - Image Fitness 518 | English Manual - Page 17
Washers (2) and two 3/8" Nylock Nuts (1). Tighten two 8mm x 3/4" Bolts (6) into the Right Weight Guide Top (78) to secure the upper ends of the Weight Guides (56). Tighten two 8mm x 3/4" Bolts into the Left Weight Guide Top (79). 44. Find Cable #1 (91). Note: There is a label attached to one end - Image Fitness 518 | English Manual - Page 18
47. Wrap Cable #1 (91).around the.lower Pulley 47 (9) on the. Adjuster (103). Insert the end of Cable #1 (91) through the indicated hole in the Front Upright (72). Lay Cable #1 (91) over another Pulley (9). Attach the Pulley to the indicated bracket on the Front Upright (72) with a 3/8" x 2" - Image Fitness 518 | English Manual - Page 19
Clip 81 C. Clip 52 I 9 8 52. Find Cable #2 (92). Insert the eyelet-end of the Cable over the top of the Pulley (9) on the Right Weight Guide Top (78). Thread the bolt-end of Cable #2 (92) into the indicated Weight Selector (57) until about half the threads are inside the Weight Selector - Image Fitness 518 | English Manual - Page 20
3/8" x 2 3/4" Shank Bolt (29). Slide out the ShanMolt until you can insert the eyelet-end of Cable #2 (92) around the Pulley (9) on the Leg Press Support (99). Slide the Shank Bolt back in and reattach the 3/8" Nylock Nut (1) and 3/8" Washer (2). 56. Route the eyelet-end of Cable #2 (92) around the - Image Fitness 518 | English Manual - Page 21
57. Attach two Pulleys (9) to the Swivel Bracket 57 (51) with 3/8" x 2" Shank Bolts (8) and 3/8" Nylock Nuts (1). 58. Find Cable #3 (93). Attach one end of the 58 Cable to the Right Butterfly Arm (75) with an 8mm x 3/4" Bolt (6), two 8mm Washers (4) and an 8mm Nylock Nut (42). Do not over- - Image Fitness 518 | English Manual - Page 22
61. Find Cable #4 (94). Insert the eyelet-end of 61 the Cable over the top of the Pulley (9) on the Left Weight Guide Top (79). Thread the bolt-end of Cable #4 (94) into the indicated Weight Selector (57) until about half the threads are inside the Weight Selector. - Image Fitness 518 | English Manual - Page 23
63. Find Cable #5 (95). Insert the eyelet-end of 63 the Cable under the Pulley (9) at the lower end of the Leg Lever (71). Route the eyelet-end of Cable #5 (95) under the indicated Pulley (9) on the "U" Stabilizer (83). Insert the eyelet-end of Cable #5 (95) through the hole in the lower end of - Image Fitness 518 | English Manual - Page 24
parts are tightened securely. The use of all remaining parts will be explained in USING THE IMAGE 518, beginning on page 27 of this owner's manual. 69. Before using the IMAGE 518 not move smoothly, locate and correct the problem before using the IMAGE 518. IMPORTANT: If the cables are not properly routed - Image Fitness 518 | English Manual - Page 25
CABLE DIAGRAMS Cable #1 (91) Cable #2 (92) O 00% O Cable #1 (91) Cable #3 (93) Cable #2 (92) 4 • • AM 40; 1" 25 - Image Fitness 518 | English Manual - Page 26
Cable #4 (94) .1; Cable #5 (95) :AG.*•;' - Image Fitness 518 | English Manual - Page 27
USING THE IMAGE 518 The instructions below describe how each component of the IMAGE 518 can be adjusted. See the Exercise Guide accompanying this owner's manual to see how the IMAGE 518 should be set up for each individual exercise. ADJUSTING THE HEIGHT OF THE SMALL SEAT 1. Turn the Lock Knob (46 - Image Fitness 518 | English Manual - Page 28
ADJUSTING THE PADS ON THE SMALL SEAT The 6" Foam Pads (59) on the Leg Press Frame (101) can be adjusted to any of three heights. To change the height, first slide one Foam Pad off the Pad Tube (58). Remove the Pad Tube and 59 insert it into a different hole in the Leg Press Frame. Slide the - Image Fitness 518 | English Manual - Page 29
ATTACHING THE LAT BAR, ROWER BAR, HAND STRAP OR AB STRAP TO THE HIGH CABLE The Lat Bar (90) can be attached to the high cable with a Cable Clip (48). For some exercises, the Long Chain (82) should be attached between the Lat Bar and the high cable with two Cable Clips. The length of Chain between - Image Fitness 518 | English Manual - Page 30
TROUBLE-SHOOTING AND=MAINTENANCE Inspect and tighten all parts of the IMAGE 518 regularly. Replace any worn part immediately. The IMAGE 518 cables cannot be tightened enough by turn- ing the bolts, follow the instructions below. ADJUSTING THE SHORT CHAINS Find the bolts on the ends of Cable #2 - Image Fitness 518 | English Manual - Page 31
Lever Leg Press "H" Frame Leg Press Support Leg Press Rail Leg Press Frame Press Arm Adjuster Leg Press Plate Long Seat Post Leg Press Base Rower Bar Ankle Strap Hand Strap Ab Strap Bumper Cap Weight Decal Sheet Owner's Manual Exercise Guide Exploded Drawing/Part ID Chart Grease Note: "#" indicates - Image Fitness 518 | English Manual - Page 32
BE HONORED BY IMAGE, INC. IF MORE INFORMATION IS REQUIRED, YOU MAY CALL DIRECTLY: 1-800-753-4645 ONE YEAR WARRANTY ON PARTS FIVE YEAR please tell our Customer Service Department the product's. name, serial number and purchase date as well as the nature of the problem, and ask for authorizatior
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
 |
 |
1
IV
E
Model
No.
IM518021
Serial
No.
The
serial
number
can
be
found
in
the
location
shown
below.
Write
the
serial
number
in
the
space
above.
Serial
Number
Decal
11
lk
,-411114%.
•
1
t
00.
,
wry
•
ii• 'V0
—
... ""
........
-
ow
•••
.......
vol.
...
., .
•••.
a..
...
....
mr,,..,,..
.
oi..
,
,..,
00
...••■•••
•
..,
.....
,
•••
....
.....
O
1
I
'ft"
....
sm.
6!1
.
.. 4•0
0
...so*
....
/..
....
I
...i
ir.,
....
II
.......
7
"
1`%
:
I;
"III
Ei
........
e
......
......
.
i
-.
e
Ms...
°.
e,.
4
44
IIIIIIIMW
OWNER'S
MANUAL
CAUTION!:
Read
all
safety
precautions
and
instructions
In
this
manual
before
using
this
equipment.
Keep
this
manual
in
a
safe
place
for
future
reference.