Insignia NS-DFLMR1 Quick Setup Guide (English) - Page 2

SETTING UP YOUR RING FLASH Attaching the control unit 1 Make sure your camera and ring flash are turned off. 2 Turn the locking ring counterclockwise to loosen it. 3 Slide the mounting foot of the control unit into your camera's hot shoe. 4 Turn the locking ring clockwise to lock the control unit in place. Attaching the flash ring 1 Select the appropriate lens adapter, then screw it onto your camera lens. Note: Remove filters from your camera before attaching the adapter. 2 Slide the flash ring onto the lens adapter until it is locked in place. Using your ring flash 1 Slide the power switch to ON. The flash begins charging and the charging indicator lights orange when the ring flash is ready to use. 2 Press + or - to select the flash power level. 3 Use your camera as usual while making sure to let the flash ring to cool down periodically. Over-use will turn on temperature protection, depending on your flash power level: Flash power level 1/1, 1/2 1/4, 1/8 1/16 # of flashes 50 100 200 Note: If temperature protection turns on, you must wait 10-25 seconds between each flash. Turn off the ring flash for about 10 minutes to return to normal operation. If the inner circuit overheats, it will shut down automatically. 4 Slide the power switch to OFF when you are finished. Note: The ring flash will enter sleep mode if idle for 30 minutes. Press any button to wake it. Note: If you want to mount the control unit separately from your camera, you need a PC sync cable (not included). SPECIFICATIONS Power 4 AAA batteries (alkaline or Ni-MH) # of Flash Cycles 300 - 1000 times (with alkaline) Recycle time .1~2 seconds Color temperature 5600K +/- 200K Flash duration 1/300-1/5000 second Dimensions Ring flash: 5 x 4.1 x 1.1 in. (128 x 103 x 28 mm) Control unit: 3 x 2.4 x 6.3 in. (75 x 60 x 160 mm) Weight .8 lbs. (370 g) SAFETY INFORMATION • Keep away from water to prevent fire, electric shock, or damage. The ring flash is not water resistant. • The ring flash contains high voltage electric parts. Do not try to open or repair it. If you touch the high-voltage circuit inside this product, electric shock may occur. • If the unit is broken and the inside is exposed, stop using it to prevent electric shock. • Do not direct the flash near eyes at short distances or eye damage may occur. When taking a flash picture towards a baby, it is recommended that you are at least 1 meter (3.3 feet) away, use a diffuser, or bounce the light away to soften the intensity. • Keep the batteries or other small parts out of children's reach. If a part is swallowed, see a doctor immediately. • If the batteries are leaking, wear gloves when you remove them. • Do not use the ring flash near flammable gas or chemicals. It may cause fire or electromagnetic interference. • Do not leave or store the ring flash in temperatures above 104°F (40°C). • Remove the batteries and store the ring flash in a dry area if it will not be used for a while. ONE-YEAR LIMITED WARRANTY For complete warranty, visit www.insigniaproducts.com. CONTACT INSIGNIA For customer service, call 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) www.insigniaproducts.com INSIGNIA is a trademark of Best Buy and its affiliated companies. Registered in some countries. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2014 Best Buy. All rights reserved. Made in China Legal notices FCC Part 15 This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply within the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC warning Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user's authority to operate this equipment. V1 ENGLISH 14-0801