Intel D410PT Intel Desktop Board D410PT Technical Product Specification - Page 20

USB, 1.5.3 SATA Support, Intel Desktop Board D410PT Technical Product Specification - driver

Get Intel D410PT PDF manuals and user guides View all Intel D410PT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Intel Desktop Board D410PT Technical Product Specification 1.5.2 USB The board provides up to eight USB 2.0 ports, supports UHCI and EHCI, and uses UHCI- and EHCI-compatible drivers. The port arrangement is as follows: • Four ports are implemented with stacked back panel connectors • Four ports are implemented with two dual port internal headers for front panel cabling NOTE Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device is attached to the cable. Use shielded cable that meets the requirements for full-speed devices. For information about The location of the USB connectors on the back panel The location of the front panel USB headers Refer to Figure 8, page 39 Figure 10, page 41 1.5.3 SATA Support The board provides two SATA interface connectors that support one device per connector. The board's SATA controller offers independent SATA ports with a theoretical maximum transfer rate of 3.0 Gbits/sec on each port. One device can be installed on each port for a maximum of two SATA devices. A point-to-point interface is used for host to device connections, unlike PATA which supports a master/slave configuration and two devices on each channel. For compatibility, the underlying SATA functionality is transparent to the operating system. The SATA controller supports IDE and AHCI configuration and can operate in both legacy and native modes. In legacy mode, standard ATA I/O and IRQ resources are assigned (IRQ 14 and 15). In Native mode, standard PCI Conventional bus resource steering is used. Native mode is the preferred mode for configurations using the Windows* XP and Windows Vista* operating systems. For information about Obtaining AHCI driver The location of the SATA connectors Refer to Section 1.2, page 16 Figure 10, page 41 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Intel Desktop Board D410PT Technical Product Specification
20
1.5.2
USB
The board provides up to eight USB 2.0 ports, supports UHCI and EHCI, and uses
UHCI- and EHCI-compatible drivers.
The port arrangement is as follows:
•
Four ports are implemented with stacked back panel connectors
•
Four ports are implemented with two dual port internal headers for front panel
cabling
NOTE
Computer systems that have an unshielded cable attached to a USB port may not
meet FCC Class B requirements, even if no device is attached to the cable.
Use
shielded cable that meets the requirements for full-speed devices.
For information about
Refer to
The location of the USB connectors on the back panel
Figure 8, page 39
The location of the front panel USB headers
Figure 10, page 41
1.5.3
SATA Support
The board provides two SATA interface connectors that support one device per
connector.
The board’s SATA controller offers independent SATA ports with a theoretical
maximum transfer rate of 3.0 Gbits/sec on each port.
One device can be installed on
each port for a maximum of two SATA devices.
A point-to-point interface is used for
host to device connections, unlike PATA which supports a master/slave configuration
and two devices on each channel.
For compatibility, the underlying SATA functionality is transparent to the operating
system.
The SATA controller supports IDE and AHCI configuration and can operate in
both legacy and native modes.
In legacy mode, standard ATA I/O and IRQ resources
are assigned (IRQ 14 and 15).
In Native mode, standard PCI Conventional bus
resource steering is used.
Native mode is the preferred mode for configurations using
the Windows* XP and Windows Vista* operating systems.
For information about
Refer to
Obtaining AHCI driver
Section 1.2, page 16
The location of the SATA connectors
Figure 10, page 41