Intel D865PCK D865PCK Technical Product Specification - Page 19

Integrator's Notes, Notes - driver

Get Intel D865PCK PDF manuals and user guides View all Intel D865PCK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Product Description AGP is a high-performance interface for graphics-intensive applications, such as 3D applications. While based on the PCI Local Bus Specification, Rev. 2.2, AGP is independent of the PCI bus and is intended for exclusive use with graphical display devices. AGP overcomes certain limitations of the PCI bus related to handling large amounts of graphics data with the following features: • Pipelined memory read and write operations that hide memory access latency • Demultiplexing of address and data on the bus for nearly 100 percent efficiency # INTEGRATOR'S NOTES • AGP 2x operation is not supported. • Install memory in the DIMM sockets prior to installing the AGP video card to avoid interference with the memory retention mechanism. • The AGP connector is keyed for Universal 0.8 V AGP 3.0 cards or 1.5 V AGP 2.0 cards only. Do not attempt to install a legacy 3.3 V AGP card. The AGP connector is not mechanically compatible with legacy 3.3 V AGP cards. For information about The location of the AGP connector Refer to Figure 1, page 11 1.5.2 USB The board supports up to six USB 2.0 ports, supports UHCI and EHCI, and uses UHCI- and EHCIcompatible drivers. The ICH5 provides the USB controller for all ports. The port arrangement is as follows: • Two ports are implemented with stacked back panel connectors, adjacent to the PS/2 connectors • Two ports are implemented with stacked back panel connectors, adjacent to the audio connectors • Two ports are routed to a front panel USB connector NOTES • Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device is attached to the cable. Use shielded cable that meets the requirements for full-speed devices. • Native USB 2.0 support has been tested with drivers for Windows* 2000 (with Service Pack 3) and Windows XP (with Service Pack 1) and is not currently supported by any other operating system. Check Intel's Desktop Board website for possible driver updates for other operating systems. For information about The location of the USB connectors on the back panel The location of the front panel USB connector Refer to Figure 8, page 38 Figure 12, page 46 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Product Description
19
AGP is a high-performance interface for graphics-intensive applications, such as 3D applications.
While based on the
PCI Local Bus Specification
, Rev. 2.2, AGP is independent of the PCI bus and
is intended for exclusive use with graphical display devices.
AGP overcomes certain limitations of
the PCI bus related to handling large amounts of graphics data with the following features:
•
Pipelined memory read and write operations that hide memory access latency
•
Demultiplexing of address and data on the bus for nearly 100 percent efficiency
INTEGRATOR’S NOTES
•
AGP 2x operation is not supported.
•
Install memory in the DIMM sockets prior to installing the AGP video card to avoid
interference with the memory retention mechanism.
•
The AGP connector is keyed for Universal 0.8 V AGP 3.0 cards or 1.5 V AGP 2.0 cards only.
Do not attempt to install a legacy 3.3 V AGP card.
The AGP connector is not mechanically
compatible with legacy 3.3 V AGP cards.
For information about
Refer to
The location of the AGP connector
Figure 1, page 11
1.5.2
USB
The board supports up to six USB 2.0 ports, supports UHCI and EHCI, and uses UHCI- and EHCI-
compatible drivers.
The ICH5 provides the USB controller for all ports.
The port arrangement is as follows:
•
Two ports are implemented with stacked back panel connectors, adjacent to the PS/2
connectors
•
Two ports are implemented with stacked back panel connectors, adjacent to the audio
connectors
•
Two ports are routed to a front panel USB connector
±
NOTES
•
Computer systems that have an unshielded cable attached to a USB port may not meet FCC
Class B requirements, even if no device is attached to the cable.
Use shielded cable that meets
the requirements for full-speed devices.
•
Native USB 2.0 support has been tested with drivers for Windows* 2000 (with Service Pack 3)
and Windows XP (with Service Pack 1) and is not currently supported by any other operating
system.
Check Intel’s Desktop Board website for possible driver updates for other operating
systems.
For information about
Refer to
The location of the USB connectors on the back panel
Figure 8, page 38
The location of the front panel USB connector
Figure 12, page 46