Intel D945GRW Product Guide - Page 18

Hi-Speed USB 2.0 Support - bios

Get Intel D945GRW - Desktop Board Motherboard PDF manuals and user guides
UPC - 735858180474
View all Intel D945GRW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Intel Desktop Board D945GRW Product Guide RJ-45 LAN Connector LEDs Two LEDs are built into the RJ-45 LAN connector located on the back panel (see Figure 2). Figure 2. LAN Connector LEDs Table 5 describes the LED states when the board is powered up and the 10/100/1000 Gigabit Ethernet LAN subsystem is operating. Table 5. LED Left (A) Right (B) RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs LED Color Green N/A Green Yellow LED State Off On Blinking Off On On Indicates LAN link is not established LAN link is established LAN activity is occurring 10 Mb/s data rate 100 Mb/s data rate 1000 Mb/s data rate Hi-Speed USB 2.0 Support NOTE Computer systems that have an unshielded cable attached to a USB port might not meet FCC Class B requirements, even if no device or a low-speed USB device is attached to the cable. Use a shielded cable that meets the requirements for a full-speed USB device. The desktop board supports up to eight USB 2.0 ports via ICH7; six ports routed to the back panel and two routed to one internal USB 2.0 header. USB 2.0 ports are backward compatible with USB 1.1 devices. USB 1.1 devices will function normally at USB 1.1 speeds. USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer rates. Disabling Hi-Speed USB in the BIOS reverts all USB 2.0 ports to USB 1.1 operation. This may be required to accommodate operating systems that do not support USB 2.0. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Intel Desktop Board D945GRW Product Guide
18
RJ-45 LAN Connector LEDs
Two LEDs are built into the RJ-45 LAN connector located on the back panel (see Figure 2).
Figure 2.
LAN Connector LEDs
Table 5 describes the LED states when the board is powered up and the 10/100/1000 Gigabit
Ethernet LAN subsystem is operating.
Table 5.
RJ-45 10/100/1000 Gigabit Ethernet LAN Connector LEDs
LED
LED Color
LED State
Indicates
Left (A)
Off
LAN link is not established
Green
On
LAN link is established
Blinking
LAN activity is occurring
N/A
Off
10 Mb/s data rate
Green
On
100 Mb/s data rate
Right (B)
Yellow
On
1000 Mb/s data rate
Hi-Speed USB 2.0 Support
NOTE
Computer systems that have an unshielded cable attached to a USB port might not meet FCC
Class B requirements, even if no device or a low-speed USB device is attached to the cable.
Use a shielded cable that meets the requirements for a full-speed USB device.
The desktop board supports up to eight USB 2.0 ports via ICH7; six ports routed to the back
panel and two routed to one internal USB 2.0 header.
USB 2.0 ports are backward compatible with
USB 1.1 devices.
USB 1.1 devices will function normally at USB 1.1 speeds.
USB 2.0 support requires both an operating system and drivers that fully support USB 2.0 transfer
rates.
Disabling Hi-Speed USB in the BIOS reverts all USB 2.0 ports to USB 1.1 operation.
This
may be required to accommodate operating systems that do not support USB 2.0.