Intel P4000M P4000M family Service Guide - Page 45

Removing and Installing 8x3.5'' Hot-swap Hard Drive, Cage Assembly

Get Intel P4000M PDF manuals and user guides View all Intel P4000M manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Hardware Installations and Upgrades 10. Install the chassis cover. For instructions, see "Installing the Chassis Cover". 11. Plug all peripheral devices and the AC power cable into the server. 12. Power up the server. Removing and Installing 8x3.5'' Hot-swap Hard Drive Cage Assembly NOTE This procedure applies only to the Intel® Server Chassis P4000M family with 8x3.5'' hot-swap hard disk drive cage configuration. Removing 8x3.5'' Hot-swap Hard Drive Cage Assembly 1. Observe the safety and ESD precautions at the beginning of this book. 2. Power down the server and unplug all peripheral devices and the AC power cable. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover". 4. Remove the front bezel if it is installed. For instructions, see "Removing the Front Bezel (Pedestal Only)". 5. Disconnect the power and data cables to the backplane. 6. Use screwdriver to release the hot-swap hard drive cage (see letter A) from the chassis and remove the hot-swap hard drive cage (see letter B). Figure 46. Removing the 8x3.5'' Hot-swap HDD Cage Assembly Installing 8x3.5'' Hot-swap Hard Drive Cage Assembly CAUTION It is critical that you connect the SAS/SATA data cables correctly from the SAS/SATA backplane to your server board or RAID controller card. Failure to do so may result in data loss. 32 Intel® Server Chassis P4000M Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
Hardware Installations and Upgrades
32
Intel
®
Server Chassis P4000M Service Guide
10.
Install the chassis cover. For instructions, see “Installing the Chassis Cover”.
11. Plug all peripheral devices and the AC power cable into the server.
12. Power up the server.
Removing and Installing 8x3.5'' Hot-swap Hard Drive
Cage Assembly
NOTE
This procedure applies only to the Intel
®
Server Chassis P4000M family with 8x3.5'' hot-swap hard disk
drive cage configuration.
Removing 8x3.5'' Hot-swap Hard Drive Cage Assembly
1.
Observe the safety and ESD precautions at the beginning of this book.
2.
Power down the server and unplug all peripheral devices and the AC power cable.
3.
Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.
4.
Remove the front bezel if it
is installed. For instructions, see “Removing the Front Bezel
(Pedestal
Only)
”.
5.
Disconnect the power and data cables to the backplane.
6.
Use screwdriver to release the hot-swap hard drive cage (see letter
A
) from the chassis and remove
the hot-swap hard drive cage (see letter
B
).
Figure 46. Removing the 8x3.5
''
Hot-swap HDD Cage Assembly
Installing 8x3.5'' Hot-swap Hard Drive Cage Assembly
CAUTION
It is critical that you connect the SAS/SATA data cables correctly from the SAS/SATA backplane to
your server board or RAID controller card. Failure to do so may result in data loss.