Intel P4000M P4000M family Service Guide - Page 47

Removing and Installing 8x3.5'' Hot-swap Backplane

Get Intel P4000M PDF manuals and user guides View all Intel P4000M manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Hardware Installations and Upgrades 7. Install the front bezel. For instructions, see "Installing the Front Bezel (Pedestal Only)". 8. Install the air duct if the air duct is removed. For instructions, see "Installing the Airduct". 9. Install the chassis cover. For instructions, see "Installing the Chassis Cover". 10. Plug all peripheral devices and the AC power cable into the server. 11. Power up the server. Removing and Installing 8x3.5'' Hot-swap Backplane NOTE This procedure applies only to the Intel® Server Chassis P4000M family with 8x3.5'' hot-swap hard disk drive cage configuration. Removing 8x3.5'' Hot-swap Backplane 1. Observe the safety and ESD precautions at the beginning of this book. 2. Power down the server and unplug all peripheral devices and the AC power cable. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover". 4. Remove the front bezel if it is installed. For instructions, see "Removing the Front Bezel (Pedestal Only)". 5. Remove the 8x3.5'' Hot-swap Hard drives cage. For instructions, see "Removing 8x3.5'' Hot-swap Hard Drive Cage Assembly". 6. Remove all hot-swap drive carriers, regardless of whether or not a drive is installed in the carrier. 7. Remove the screws on the backplane (see letter A). 8. Push the backplane (see letter B) and remove the backplane from the cage (see letter C). Figure 49. Removing 8x3.5" Hot-swap Backplane 34 Intel® Server Chassis P4000M Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
Hardware Installations and Upgrades
34
Intel
®
Server Chassis P4000M Service Guide
7.
Install the front bezel. For i
nstructions, see “Installing the Front
Bezel (Pedestal Only)
”.
8.
Install the air duct if the air duct is removed. For instructions, see
“
Installing the Airduct
”
.
9.
Install the chassis cover. For instructions, see “Installing the Chassis Cover”.
10. Plug all peripheral devices and the AC power cable into the server.
11. Power up the server.
Removing and Installing 8x3.5'' Hot-swap Backplane
NOTE
This procedure applies only to the Intel
®
Server Chassis P4000M family with 8x3.5'' hot-swap hard
disk drive cage configuration.
Removing 8x3.5'' Hot-swap Backplane
1.
Observe the safety and ESD precautions at the beginning of this book.
2.
Power down the server and unplug all peripheral devices and the AC power cable.
3.
Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.
4.
Remove the front bezel if it is installed. For
instructions, see “Removing the Front Bezel
(Pedestal
Only)
”.
5.
Remove the 8x3.5'' Hot-swap Hard drives cage. F
or instructions, see “Removing
8x3.5'' Hot-swap
Hard Drive Cage Assembly
”.
6.
Remove all hot-swap drive carriers, regardless of whether or not a drive is installed in the carrier.
7.
Remove the screws on the backplane (see letter
A
).
8.
Push the backplane (see letter
B
) and remove the backplane from the cage (see letter
C
).
Figure 49. Removing 8x3.5
”
Hot-swap Backplane