Home » Intel Manuals » Servers » Intel S1400FP » Manual Viewer

Intel S1400FP Intel Server Board S1400FP Technical Product Specification - Page 107

Management Engine (ME) Firmware Force Update Jumper Block, 9.3 Password Clear Jumper Block

Get Intel S1400FP PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

Intel® Server Board S1400FP TPS Jumper Blocks 11. Configure desired BIOS settings 9.2 Management Engine (ME) Firmware Force Update Jumper Block When the ME Firmware Force Update jumper is moved from its default position, the ME is forced to operate in a reduced minimal operating capacity. This jumper should only be used if the ME firmware has gotten corrupted and requires re-installation. The following procedure should be followed. Note: System Update and Recovery files are included in the System Update Packages (SUP) posted to Intel®'s web site. 1. Turn off the system and remove power cords. 2. Move the ME FRC UPD Jumper from the default (pins 1 and 2) operating position to the Force Update position (pins 2 and 3). 3. Re-attach system power cords. 4. Power on the system. Note: System Fans will boost and the BIOS Error Manager should report an 83A0 error code (ME in recovery mode). 5. Boot to the EFI shell and update the ME firmware using the "MEComplete####.cap" file (where #### = ME revision number) using the following command: iflash32 /u /ni MEComplete####.cap. 6. When update has successfully completed, power off system. 7. Remove AC power cords. 8. Move ME FRC UPD jumper back to the default position. Note: If the ME FRC UPD jumper is moved with AC power applied, the ME will not operate properly. The system will need have the AC power cords removed, wait for at least 10 seconds and then reinstalled to ensure proper operation. 9. Install AC power cords. 10. Power on system. 9.3 Password Clear Jumper Block This jumper causes both the User password and the Administrator password to be cleared if they were set. The operator should be aware that this creates a security gap until passwords have been installed again through the BIOS Setup utility. This is the only method by which the Administrator and User passwords can be cleared unconditionally. Other than this jumper, passwords can only be set or cleared by changing them explicitly in BIOS Setup or by similar means. No method of resetting BIOS configuration settings to default values will affect either the Administrator or User passwords. 1. Power down the server and unplug the power cords. 2. Move jumper from the default (pins 1 and 2) operating position to the password clear position (pins 2 and 3). 3. Close the server chassis and reattach the power cords. 4. Power up the server and wait until POST completes. Note: BIOS Error Manager should report a 5224 and 5221 error codes (Password clear jumper is set and Passwords cleared by jumper). 5. Power down the server and unplug the power cords. 6. Open the chassis, remove the Riser #2 assembly, and move the jumper back to the default position (covering pins 1 and 2). Revision 1.0 95 Intel order number G64246-001

Section	Page
1. Introduction	13
1.1 Chapter Outline	13
1.2 Server Board Use Disclaimer	13
2. Overview	14
2.1 Intel® Server Boards S1400FP Feature Set	14
2.2 Server Board Layout	16
2.2.1 Server Board Connector and Component Layout	16
2.2.2 Server Board Mechanical Drawings	19
2.2.3 Server Board Rear I/O Layout	25
3. Functional Architecture	27
3.1 Processor Support	28
3.1.1 Processor Socket Assembly	28
3.2 Processor Function Overview	28
3.2.1 Intel® QuickPath Interconnect	29
3.2.2 Integrated Memory Controller (IMC) and Memory Subsystem	30
3.2.2.1 Supported Memory	31
3.2.2.2 Memory population rules	32
3.2.2.3 Publishing System Memory	34
3.2.2.4 RAS Features	34
3.2.2.4.1 Independent Channel Mode	35
3.2.2.4.2 Rank Sparing Mode	35
3.2.2.4.3 Mirrored Channel Mode	36
3.2.2.4.4 Lockstep Channel Mode	36
3.2.2.5 Single Device Data Correction (SDDC)	37
3.2.2.6 Error Correction Code (ECC) Memory	37
3.2.2.6.1 Correctable Memory ECC Error Handling	37
3.2.2.6.2 Uncorrectable Memory ECC Error Handling	38
3.2.2.7 Demand Scrubbing for ECC Memory	38
3.2.2.8 Patrol Scrubbing for ECC Memory	38
3.2.3 Processor Integrated I/O Module (IIO)	38
3.2.3.1 Network Interface	40
3.3 Intel® C602 (-A) Chipset Functional Overview	40
3.3.1 Digital Media Interface (DMI)	41
3.3.2 PCI Express* Interface	41
3.3.3 Serial ATA (SATA) Controller	42
3.3.4 AHCI	42
3.3.5 Rapid Storage Technology	42
3.3.6 PCI Interface	42
3.3.7 Low Pin Count (LPC) Interface	42
3.3.8 Serial Peripheral Interface (SPI)	42
3.3.9 Compatibility Modules (DMA Controller, Timer/Counters, Interrupt Controller)	43
3.3.10 Advanced Programmable Interrupt Controller (APIC)	43
3.3.11 Universal Serial Bus (USB) Controller	43
3.3.12 Gigabit Ethernet Controller	43
3.3.13 RTC	44
3.3.14 GPIO	44
3.3.15 Enhanced Power Management	44
3.3.16 Manageability	44
3.3.17 System Management Bus (SMBus* 2.0)	45
3.3.18 Intel® Active Management Technology (Intel® AMT)	45
3.3.19 Integrated NVSRAM Controller	45
3.3.20 Intel® Virtualization Technology for Direct I/O (Intel® VT-d)	45
3.3.21 JTAG Boundary-Scan	45
3.3.22 KVM/Serial Over LAN (SOL) Function	46
3.3.23 On-board Serial Attached SCSI (SAS)/Serial ATA (SATA) Support and Options	46
3.3.23.1 Intel® Embedded Server RAID Technology 2 (ESRT2)	47
3.3.23.2 Intel® Rapid Storage Technology (RSTe)	48
3.4 Integrated Baseboard Management Controller (BMC) Overview	48
3.4.1 Super I/O Controller	49
3.4.1.1 Keyboard and Mouse Support	50
3.4.1.2 Wake-up Control	50
3.4.2 Graphics Controller and Video Support	50
3.4.3 Baseboard Management Controller	51
3.4.3.1 Remote Keyboard, Video, Mouse, and Stoerage (KVMS) Support	51
3.4.3.2 Integrated BMC Embedded LAN Channel	52
4. System Security	53
4.1 BIOS Password Protection	53
4.2 Trusted Platform Module (TPM) Support	54
4.2.1 TPM security BIOS	54
4.2.2 Physical Presence	55
4.2.3 TPM Security Setup Options	55
4.2.3.1 Security Screen	56
4.3 Intel® Trusted Execution Technology	57
5. Technology Support	59
5.1 Intel® Trusted Execution Technology	59
5.2 Intel® Virtualization Technology – Intel® VT-x/VT-d/VT-c	59
5.3 Intel® Intelligent Power Node Manager	60
5.3.1 Hardware Requirements	61
6. Platform Management Functional Overview	62
6.1 Baseboard Management Controller (BMC) Firmware Feature Support	62
6.1.1 IPMI 2.0 Features	62
Non IPMI Features	63
6.1.2 New Manageability Features	64
6.2 Basic and Advanced Features	65
6.3 Integrated BMC Hardware: Emulex* Pilot III	66
6.3.1 Emulex* Pilot III Baseboard Management Controller Functionality	66
6.4 Advanced Configuration and Power Interface (ACPI)	67
6.5 Power Control Sources	67
6.6 BMC Watchdog	68
6.7 Fault Resilient Booting (FRB)	68
6.8 Sensor Monitoring	69
6.9 Field Replaceable Unit (FRU) Inventory Device	69
6.10 System Event Log (SEL)	70
6.11 System Fan Management	70
6.11.1 Thermal and Acoustic Management	70
6.11.2 Setting Throttling Mode	71
6.11.3 Altitude	71
6.11.4 Set Fan Profile	71
6.11.5 Fan PWM Offset	71
6.11.6 Quiet Fan Idle Mode	71
6.11.7 Fan Profiles	72
6.11.8 Thermal Sensor Input to Fan Speed Control	72
6.11.9 Memory Thermal Throttling	74
6.12 Messaging Interfaces	74
6.12.1 User Model	75
6.12.2 IPMB Communication Interface	75
6.12.3 LAN Interface	75
6.12.3.1 RMCP/ASF Messaging	76
6.12.3.2 BMC LAN Channels	76
6.12.3.2.1 Baseboard NICs	76
6.12.3.2.2 Dedicated Management Channel	76
6.12.3.2.3 Concurrent Server Management Use of Multiple Ethernet Controllers	77
6.12.3.3 IPV6 Support	78
6.12.3.4 LAN Failover	78
6.12.3.5 BMC IP Address Configuration	79
6.12.3.5.1 Static IP Address (IP Address Source Values 0h, 1h, and 3h)	79
6.12.3.5.2 Static LAN Configuration Parameters	79
6.12.3.5.3 Enabling/Disabling Dynamic Host Configuration (DHCP) Protocol	80
6.12.3.5.4 DHCP-related LAN Configuration Parameters	80
6.12.3.6 DHCP BMC Hostname	81
6.12.4 Address Resolution Protocol (ARP)	81
6.12.5 Internet Control Message Protocol (ICMP)	81
6.12.6 Virtual Local Area Network (VLAN)	82
6.12.7 Secure Shell (SSH)	82
6.12.8 Serial-over-LAN (SOL 2.0)	82
6.12.9 Platform Event Filter (PEF)	83
6.12.10 LAN Alerting	83
6.12.10.1 SNMP Platform Event Traps (PETs)	84
6.12.11 Alert Policy Table	84
6.12.11.1 E-mail Alerting	84
6.12.12 SM-CLP (SM-CLP Lite)	84
6.12.13 Embedded Web Server	85
6.12.14 Virtual Front Panel	86
6.12.15 Embedded Platform Debug	87
6.12.15.1 Output Data Format	88
6.12.15.2 Output Data Availability	88
6.12.15.3 Output Data Categories	88
6.12.16 Data Center Management Interface (DCMI)	89
6.12.17 Lightweight Directory Authentication Protocol (LDAP)	89
7. Advanced Management Feature Support (RMM4)	90
7.1 Keyboard, Video, Mouse (KVM) Redirection	91
7.1.1 Remote Console	92
7.1.2 Performance	92
7.1.3 Security	93
7.1.4 Availability	93
7.1.5 Usage	93
7.1.6 Force-enter BIOS Setup	93
7.2 Media Redirection	93
7.2.1 Availability	94
7.2.2 Network Port Usage	94
8. On-board Connector/Header Overview	95
8.1 Board Connector Information	95
8.2 Power Connectors	96
8.3 System Management Headers	97
8.3.1 Intel® Remote Management Module 4 Connector	97
8.3.2 TPM connector	98
8.3.3 Intel® RAID C600 Upgrade Key Connector	98
8.3.4 Local Control Panel Header	98
8.3.5 HSBP_I2C Header	98
8.3.6 HDD LED Header	98
8.3.7 Chassis Intrusion Header	99
8.3.8 SATA SGPIO Header	99
8.3.9 SAS SGPIO Header	99
8.3.10 IPMB Connector	99
8.4 Front Panel Connector	99
8.4.1 Power / Sleep Button and LED Support	100
8.4.2 System ID Button and LED Support	100
8.4.3 System Reset Button Support	100
8.4.4 NMI Button Support	101
8.4.5 NIC Activity LED Support	101
8.4.6 Hard Drive Activity LED Support	101
8.4.7 System Status LED Support	101
8.5 I/O Connectors	101
8.5.1 VGA Connector	101
8.5.2 SATA and SAS Connectors	102
8.5.3 Serial Port Connectors	102
8.5.4 USB Connector	103
8.6 Fan Headers	104
9. Jumper Blocks	105
9.1 BIOS Recovery Jumper	106
9.2 Management Engine (ME) Firmware Force Update Jumper Block	107
9.3 Password Clear Jumper Block	107
9.4 BIOS Default Jumper Block	108
9.5 BMC Force Update Jumper Block	108
10. Intel® Light Guided Diagnostics	109
10.1 System ID LED	109
10.2 System Status LED	110
10.3 BMC Boot/Reset Status LED Indicators	111
10.4 Post Code Diagnostic LEDs	112
10.5 5 Volt Stand-By Present LED	112
10.6 Fan Fault LEDs	112
10.7 Memory Fault LEDs	112
11. Environmental Limits Specification	113
11.1 Processor Thermal Design Power (TDP) Support	113
11.2 MTBF	114
12. Server Board Power Distribution	115
12.1 DC Output Specification	115
12.1.1 Output Power/Currents	115
12.1.2 Cross Loading	116
12.1.3 Standby Output	116
12.1.4 Voltage Regulation	116
12.1.5 Dynamic Loading	117
12.1.6 Capacitive Loading	117
12.1.7 Grounding	117
12.1.8 Residual Volatge Immunity in Standy mode	117
12.1.9 Common Mode Noise	118
12.1.10 Ripple/Noise	118
12.1.11 Timing Requirements	118
Appendix A: Integration and Usage Tips	121
Appendix B: Integrated BMC Sensor Tables	122
Appendix C: POST Code Diagnostic LED Decoder	146
Appendix D: POST Code Errors	151
Appendix E: Supported Intel® Server Chassis	157
Glossary	158

Match case Limit results 1 per page

Intel® Server Board S1400FP TPS

Jumper Blocks

Revision 1.0

Intel order number G64246-001

11. Configure desired BIOS settings

9.2

Management Engine (ME) Firmware Force Update Jumper Block

When the ME Firmware Force Update jumper is moved from its default position, the ME is

forced to operate in a reduced minimal operating capacity.

This jumper should only be used if

the ME firmware has gotten corrupted and requires re-installation. The following procedure

should be followed.

Note

System Update and Recovery files are included in the System Update Packages (SUP)

posted to Intel

’s web site.

Turn off the system and remove power cords.

2. Move the

ME FRC UPD

Jumper from the default (pins 1 and 2) operating position to the

Force Update position (pins 2 and 3).

3. Re-attach system power cords.

4. Power on the system.

Note

: System Fans will boost and the BIOS Error Manager should report an 83A0 error

code (ME in recovery mode).

Boot to the EFI shell and update the ME firmware using the “MEComplete####.cap” file

(where #### = ME revision number) using the following command: iflash32 /u

/ni MEComplete####.cap.

When update has successfully completed, power off system.

7. Remove AC power cords.

Move ME FRC UPD jumper back to the default position.

Note

: If the ME FRC UPD jumper is moved with AC power applied, the ME will not

operate properly. The system will need have the AC power cords removed, wait for at

least 10 seconds and then reinstalled to ensure proper operation.

9. Install AC power cords.

10. Power on system.

9.3

Password Clear Jumper Block

This jumper causes both the User password and the Administrator password to be cleared if

they were set. The operator should be aware that this creates a security gap until passwords

have been installed again through the BIOS Setup utility. This is the only method by which the

Administrator and User passwords can be cleared unconditionally. Other than this jumper,

passwords can only be set or cleared by changing them explicitly in BIOS Setup or by similar

means. No method of resetting BIOS configuration settings to default values will affect either the

Administrator or User passwords.

Power down the server and unplug the power cords.

Move jumper from the default (pins 1 and 2) operating position to the password clear

position (pins 2 and 3).

Close the server chassis and reattach the power cords.

Power up the server and wait until POST completes.

Note

: BIOS Error Manager should report a 5224 and 5221 error codes (Password clear

jumper is set and Passwords cleared by jumper).

Power down the server and unplug the power cords.

Open the chassis, remove the Riser #2 assembly, and move the jumper back to the

default position (covering pins 1 and 2).